GTO GP-SL100 Owner'S Manual Download Page 13

Page: 13 / 36

Using the Mounting Template

The mounting template

(see insert)

is designed to simplify mounting the operator. It provides the installer with

the proper locations for running power and accessory wiring conduits. The template is also marked with the

correct distance between the operator mounting holes and shows the installer how to position the operator for

the correct clearance between the housing and the gate.

NOTE:

The operator must be securely mounted on a level concrete pad. If you do not have an existing pad to work

with, be sure to install wiring conduit before pouring concrete. You must use (5)

” diameter wedge type mounting

anchors, washers, and nuts (not included) to mount the operator on the pad.

Study the mounting template. Lay the mounting template on the level concrete pad and mark the pad according

to the instructions on the template.

Before mounting the operator, check the following:

• The concrete pad is level.

• (5) 3/8” diameter mounting anchors are in their correct positions.

• Conduit for power and accessory wiring is installed.

Roller

Gate

Fence Post

Roller

Driveway

Safety Edges

(REQUIRED)

Safety Edge

(REQUIRED)

Safety Edge

(REQUIRED)

4 in to 6 in

Installation Alignment

Chain Bracket

Operator must be mounted with the chain rollers

and sprocket aligned with the chain.

Chain brackets must be installed (welded

or bolted) to provide 4 to 6 inches between

chain and inside of gate. This will ensure

adequate clearance between the operator

housing and the gate.

Mounting Operator

Concrete mounting pad 18 in x 18

in. Consult local building codes for

depth below ground level. Absolute

minimum depth 18 in below

ground level. Use

in diameter

concrete mounting bolts in

mounting pad.

18 in

(45.7cm)

18 in

(45.7 cm)

14½ in

(36.8 cm)

18 in

(45.7cm)

BELOW GROUND LEVEL

23¾ in

(60.3cm)

TO BASE

3 / in

(9.9 cm)

15 16

GROUND LE

VEL

Summary of Contents for GP-SL100





































Search results

Summary of Contents for GP-SL100

Reviews:

Brands by name

Popular brands

GTO GP-SL100, Owner'S Manual

Search results

Summary of Contents for GP-SL100

Reviews:

Brands by name

Popular brands