GSS PTIS Assembly Instructions Manual Download Page 24

Page: 24 / 36

- 24 -

Switching the IP address off or on
Selecting the transmission protocol
Setting the port number

In this menu you can switch off the IP address displayed, and
define the transmission protocol and the port number.

Switching the IP address off or on
• Press the

buttons to switch off (”

off

”) or (“

”) the

output IP address and the service referred.

—> In the second line of the ”

IP-OUT …

” menu ”

off

” is

displayed instead of the service referred.

Selecting the transmission protocol
• Press the

▶

button to position the cursor under ”

UDP

” or

”

RTP

”.

• Using the

buttons to select the transmission protocol

wished:

“

UDP

” – The User Datagram Protocol is for the connec-

tionless transmission of data to a certain applica-
tion. The port number of the service is also sent
which the data should obtain.

“

RTP

” – The Real-time Transport Protocol is for continu-

ously transmitting multimedia data streams in an
IP network. Unlike UDP, the header is transmitted
which makes the data transmission more robust.

IP-OUT 1

…

IP-OUT 16

IP 1

on UDP

MODE / PORT

1234

Bx 4

Das Erste

IP-OUT 1

on / off
UDP / RTP,
0 … 65535
copy

IP-OUT 1

…

IP-OUT 16

Bx 4

Das Erste

IP-OUT 1

Bx 4

off

IP-OUT 1

Summary of Contents for PTIS





































Search results

Summary of Contents for PTIS

Reviews:

Related manuals for PTIS

Brands by name

Popular brands

GSS PTIS, Assembly Instructions Manual

Search results

Summary of Contents for PTIS

Reviews:

Related manuals for PTIS

Brands by name

Popular brands