Grundfos TPE 2 Series Installation And Operating Instructions Manual Download Page 16

Page: 16 / 70

English (GB)

9.10 Installation altitude

Installation altitude is the height above sea level of the installation
site.
• Motors installed up to 1000 metres above sea level can be

loaded 100 %.

• Motors installed more than 1000 metres above sea level must

not be fully loaded due to the low density and consequent low
cooling effect of the air. See fig.

Fig. 25

Derating of motor output power (P2) in relation to
altitude above sea level

9.11 Humidity

Maximum humidity: 95 %.
If the humidity is constantly high and above 85 %, one of the drain
holes in the drive-end flange must be open.
See section

6. Mechanical installation

9.12 Motor cooling

To ensure cooling of motor and electronics, observe the following:
• Position the motor in such a way that adequate cooling is

ensured. See section

6.7 Ensuring motor cooling

• The temperature of the cooling air must not exceed 50 °C.
• Keep cooling fins and fan blades clean.

10. User interfaces

You can make pump settings by means of the following user
interfaces:

Control panels

• Standard control panel.

See section

11. Standard control panel

• Advanced control panel.

See section

12. Advanced control panel

Remote controls

• Grundfos GO.

See section

13. Grundfos GO

If the power supply to the pump is switched off, the settings will
be stored.

Factory settings

TPE2, TPE2 D pumps have been factory-set to constant-curve
control mode. See section

11.1.2 Pump in constant-curve control

mode

The setpoint corresponds to 100 % of the maximum pump
performance. See data booklet or Grundfos Product Center.
TPE3, TPE3 D pumps have been factory-set to AUTO

ADAPT

control mode. See section

14.5.1 AUTOADAPT

Caution

The motor must not be installed more than 2000
metres above sea level.

05 640

0 471

0.99
0.98
0.97
0.96
0.95
0.94
0.93
0.92
0.91
0.90
0.89
0.88

1000

1200

1400

1600

1800

2000 2200

[m]

P2
[%]

Altitude [m]

P2
[%]

Warning
The product may be so hot that only the buttons are
to be touched.

Summary of Contents for TPE 2 Series







































































Search results

Summary of Contents for TPE 2 Series

Reviews:

Related manuals for TPE 2 Series

Brands by name

Popular brands

Grundfos TPE 2 Series, Installation And Operating Instructions Manual

Search results

Summary of Contents for TPE 2 Series

Reviews:

Related manuals for TPE 2 Series

Brands by name

Popular brands