background image

3

(

Q

J

OLV

K

8

6

2. Symbols used in this document

3. General description 

The GRUNDFOS MAGNA Series 2000 is a circulator 
pump with integrated differential pressure control 
enabling adjustment of pump performance to the 
actual system requirements. In many systems, this 
will reduce the power consumption considerably, 
reduce noise from thermostatic valves and similar
fittings, and improve the control of the system.

The desired head can be set on the pump control 
panel.

Fig. 1

Grundfos MAGNA Series 2000 circulator 
pump

4. Applications

The GRUNDFOS MAGNA is designed for circulating 
liquids in heating and air-conditioning systems.

The pump range is primarily used in

systems with a variable flow.

The pump range can also be used in 

systems with a constant flow where it is
desirable to optimize the setting of the pump duty 
point

systems with variable flow-pipe temperature.

4.1 Pumped liquids

Grundfos MAGNA is intended for pumping clean 
water not containing solid particles or fibers.

Warning

If these safety instructions are not 
observed, it may result in personal 
injury!

&DXWLRQ

If these safety instructions are not 
observed, it may result in malfunc-
tion or damage to the equipment!

1RWH

Notes or instructions that make the 
job easier and ensure safe
operation. 

Warning

The use of this product requires 
experience with and knowledge of 
the product.

Persons with reduced physical,
sensory or mental capabilities must 
not use this product, unless they 
are under supervision or have been 
instructed in the use of the product 
by a person responsible for their 
safety.

Children must not use or play with 
this product.

TM

04

 93

89

 40

10

Warning

The pump must not be used for the 
transfer of flammable liquids such 
as diesel oil, petrol or similar
liquids. 

Summary of Contents for MAGNA 32-100

























Reviews: