background image

16

(

Q

J

OLV

K

8

6

The temperature influence function can be activated 
in this display when the control mode is proportional 
pressure or constant pressure; see section 
9.7.1 Control mode.

In the case of temperature influence, the pump must 
be installed in the flow pipe. It is possible to choose 
between maximum temperatures of
122 °F (50 °C) and 176 °F (80 °C).

When the temperature influence is active, a small 
thermometer is shown in the display "Setpoint" in 
menu OPERATION, see section 9.5.1 Setpoint.

9.7.4 Buttons on pump

To prevent unauthorized persons from operating the 
pump, the function of the buttons 

 and 

 can 

be deactivated in this display. The buttons can be 
reactivated only with the R100.

The buttons can be set to:

Active 

Not active.

9.7.5 Signal relay

If an expansion module has been fitted, the signal 
relay function can be set in this display.

Fault (functions as a fault signal relay)

Ready (functions as a ready signal relay)

Operation (functions as an operating signal 
relay).

9.7.6 Pump number

A number from 1 up to and including 64 can be
allocated to a pump or can be changed so that the 
R100, Grundfos Control MPC Series 2000 or other 
systems can distinguish between two or more 
pumps. 

9.8 Priority of settings

The external forced-control signals will influence the 
settings available on the pump control panel and with 
the R100. However, the pump can always be set to 
max. curve duty or to stop on the pump control panel 
or with the R100. 

If two or more functions are activated at the same 
time, the pump will operate according to the setting 
with the highest priority. 

The priority of the settings is as shown in the table.

Example: If the pump has been forced to stop via an 
external signal, the pump control panel or the R100 
can only set the pump to max. curve.

With expansion module

As illustrated in the table, the pump does not react to 
external signals (max. curve and min. curve) when 
the pump is controlled via bus.

If the pump is to react to external signals (max. curve 
and min. curve), the system must be configured for 
that function. 

For further details, please contact Grundfos.

1RWH

If the pump is in control mode
AUTO

ADAPT

 or constant curve, the 

temperature influence cannot be set 
with the R100.

Priority 

Possible settings

Pump

control 

panel 

or R100

External 

signals

Bus 

signal

1

Stop 

2

Max. curve 

3

Stop

Stop

4

Max.curve 

Max.curve

5

Min. curve 

Min. curve 

Min. curve

6

Setpoint 

setting

Setpoint 

setting

Not active when the pump is con-
trolled via bus.

Only active when the pump is con-
trolled via bus.

Summary of Contents for MAGNA 32-100

























Reviews: