background image

18

(

Q

J

OLV

K

8

6

10.1 Checking the module

Noise in the 
system.

Air in the system.

Vent the system.

The flow is too high.

Reduce the setpoint and possibly 
change over to AUTO

ADAPT 

or 

constant pressure.

The pressure is too high.

Reduce the setpoint and possibly 
change over to AUTO

ADAPT 

or 

proportional pressure.

Noise in the 
pump.

The inlet pressure is too low. 

Increase the inlet pressure and/or 
check air volume in the expan-
sion tank (if installed).

Air in the pump.

Set the pump to "MAX" by contin-
uously pressing the button 

 or 

with the R100. After venting, set 
the pump back to normal duty by 
pressing 

the 

buttons ,  

or 

with the R100.
Note: The pump must not run 
dry.

Indicator 

lights

Fault

Cause

Remedy

Green

Red

1

1RWH

The R100 can also be used for fault finding. 

Illustration

Action

T

M

03

 08

92

 07

0

5

1. Remove the module cover.

2. Check the LEDs.

When the pump is switched on and the 
module is correctly mounted, the left LED 
must be flashing and the right LED must 
be permanently on.

3. Refit the module cover. 

Flashing

Permanently on

Summary of Contents for MAGNA 32-100

























Reviews: