background image

15

16

5.5 SPH System electrical connection

Limit:

Max PV voltage: 550V (consider the lowest temperature)
Max PV input current: 13A

Remark: 

1. Please do not connect to DC source!
2. For RSD function, the default brand of RSD supplier is Tigo, including AP system 
and other brand RSD can be integrated. The more information please turns to 
manufacturer.

Wire suggest length

5.5.1 Connection of PV terminal

Step 1 Turn off the PV switch.
Step 2 Remove the locking nut and waterproofing bolt.
Step 3 Secure the pipe fitting to the enclosure using the nut provided with the pipe.
Step 4 Route the PV input power cable through the conduit and then fitting of the pipe.
Step  5  Connect  the  PV  input  power  cable  to  the  terminal  block.  connect  positive 
pole(+)  of  connection  cable  to  positive  pole(+)  of  PV  input  terminal  block,  connect 
negative  pole(-)  of  connection  cable  to  negative  pole(-)of  PV  input  terminal  block, 
please pay attention to PV input voltage and current within permission.
Step 6 Secure the fitting to the conduit.
Step 7 Checks that the cables are connected correctly and securely. Then take 
appropriate measures to ensure that the pipe conduit and fittings are secured reliably, 
and seal the cable holes.

5.5.2 Connection of AC terminal and off grid terminal

SPH has a grid output terminal and off grid out terminal, look down on the SPH from 
the front, the terminal on the right (on grid) is grid outlet for connecting grid, the 
terminal on the left is an uninterrupted power outlet for connecting critical load.

Conduct

or cross 

section

Max cable length

 SPH3000

SPH3600

 SPH4000

 SPH4600

 SPH5000

 SPH6000

5.2mm2 

10AWG  

40m

33m

28m

26m

25m

23m

6.6mm2 

9AWG 

50m

42m

36m

33m

32m

29m

17

mm

P

V2

-

P

E

P

V2

+

P

E

P

V1

+

P

V1

-

OFF Grid

ON Grid

Summary of Contents for SPH3000TL BL-US




































Reviews: