Groeneveld MSFi, Operation & Maintenance Manual

Page: 12 / 20

MSFI - F801306
12
Pump Type
Recommended Lubricants
Oils SAE
80/90
NLGI# 000 NLGI# 00 NLGI# 0 NLGI# 1 NLGI# 2
MSFi - 40°F ( - 40°C) - 29°F ( - 34°C) - 8°C ( - 23°C) 2°F ( - 17°C) 9°F ( - 13°C) 14°F ( - 10°C)
Upper Temp Limit +40°C (+104°F) for all pumps
Recommended Lubricants
Recommended Lubricants
The AX Pump has been developed specifically to run with NLGI Grade 000, 1, 2 grease and FG3,0 fluid grease. Oils to a minimum viscosity
of SAE80 are also acceptable.
Do not use heavy, tackified greases, greases containing bentone/bentonite or greases containing molyb-
denum and/or graphite.
NOTE: To ensure proper operation of the lubrication system, only fill with clean lubricant that has been in a sealed container and correctly
stored. Failure to use clean lubricant can result in premature system or bearing failures.
Recommended Lubricants Operational Temperatures
(Based on maximum lubricant distribution line length of 35ft/10.7m*)
*Maximum line length dependent upon environmental temperature and lubricant being used.
110/220 VAC Pump Output Combinations*
Pump
Element
Timer Setting (Delay Cycle)
#1 -
6min
#2 -
15min
#3 -
30min
#4 -
60min
Red 0.05 0.03 0.018 0.01
Green 0.075 0.044 0.025 0.014
Yellow 0.125 0.073 0.042 0.023
Blue 0.200 0.116 0.067 0.036
Grey 0.300 0.174 0.100 0.055
Black 0.500 0.290 0.167 0.091
Output shown in cc ’ s (grams) per hour.
All AX pumps come standard with blue pumping elements
set at the #3 setting. All other pumping elements sold
separately.
12/24 VDC Pump Output Combinations*
Pump
Element
Timer Setting (Delay Cycle)
#0 -
1.8rpm
#1 -
6min
#2 -
9min
#3 -
12min
#4 -
27min
#5 -
42min
#6 -
57min
Red 0.240 0.067 0.050 0.040 0.020 0.013 0.010
Green 0.360 0.101 0.075 0.060 0.030 0.020 0.015
Yellow 0.600 0.168 0.125 0.100 0.050 0.033 0.025
Blue 0.960 0.268 0.200 0.160 0.080 0.052 0.040
Grey 1.440 0.402 0.300 0.240 0.120 0.078 0.060
Black 2.400 0.670 0.500 0.400 0.200 0.130 0.100
Output shown in cc ’ s (grams) per hour.
All AC pumps come standard with blue pumping elements set at the #4 setting.
All other pumping elements sold separately.
System Output Combinations
MultiLine AXL Kits incorporate modular functionality which allows the user to increase or decrease system output by changing pumping
elements, adjusting timer settings or both. Combinations shown below.
AC Pumps
The preferred method to increase or decrease system output is through the use of the externally programmable PCB (see pages 7 - 8).
Alternatively, the blue pumping elements can be replaced with pumping elements of varying outputs (see page 5).
AX Pumps
The preferred method to increase or decrease system output is by replacing the blue pumping elements with pumping elements of
varying outputs (see page 5). Alternatively, the timer setting can be adjusted by accessing the switches on the PCB (see pages 9 - 10).
*All outputs above are approximate. The type of lubricant, line length, and environmental conditions (temperature) may affect system output.