background image

MSFI 

-

 F801306

 

 

 

 

 

Groeneveld

-

BEKA (North America) 

 

 

 

MultiLine SFi (MSFI) Manual

 

 

 

 

 

This print and the ideas and principles represented on the print are the property of Groeneveld

-

BEKA USA. This print is not to be copied or reproduced (even extracts) without prior 

written consent of Groeneveld

-

BEKA. This manual is not intended to be a substitute for the specific recommendations of your equipment supplier. Every reasonable effort has been 

made to ensure the accuracy of the information contained in this catalog, but no liability is accepted for errors, omissions or for any other reason.

 

Applicable Pumps: AC15XXL

-

2

-

A, AC25XXL

-

2

-

A, AX13XXL

-

A, AX23XXL

-

A

 

Applicable Kits: MSFI

-

XXXX

-

XXXX

 

 

Maximum Working Pressure: 1740 psi (120 bar, 12 MPa)

 

Maximum operating temperature: 140°F/60°C 

 

*(Note that operating close to maximum temperature will effect life of the pump)*

 

Minimum operating temperature: 

-

31°F/

-

35°C (with grade 000 grease),  10°F/

-

12°C (with grade 2 grease).

 

IP Rating: IP66

 

Voltage: 24 VDC, 110/220 VAC (50/60Hz)

 

Power Rating: 4VA

 

Fuse Rating: 1A

 

*Max Pumpability Distance: 35ft (10.7m)

 

*Temperature & lubricant dependent

 

 

Summary of Contents for MSFi





















Reviews: