background image

2 OM-DEE/4

IMPORTANT - READ FIRST - IMPORTANT

REGULATIONS AND SAFETY PRECAUTIONS:

THESE APPLIANCES HAVE BEEN CE MARKED ON THE BASIS OF COMPLIANCE WITH THE EMC AND LOW 

VOLTAGE DIRECTIVE. THESE APPLIANCES MUST BE INSTALLED BY A COMPETENT PERSON IN CONFORMITY 

WITH THE INSTALLATION AND SERVICING INSTRUCTIONS AND NATIONAL REGULATIONS IN FORCE AT THE 

TIME. PARTICULAR ATTENTION MUST BE PAID TO THE FOLLOWING:

 

 

I. E. E. REGULATIONS FOR ELECTRICAL INSTALLATIONS

 

ELECTRICITY AT WORK REGULATIONS

 

HEALTH AND SAFETY AT WORK ACT

 

FIRE PRECAUTIONS ACT

 

LOCAL AND NATIONAL BUILDING REGULATIONS

THOSE PARTS WHICH HAVE BEEN PROTECTED BY THE MANUFACTURER MUST NOT BE ADJUSTED BY THE 

USER. 

USERS SHOULD BE CONVERSANT WITH APPROPRIATE PROVISIONS OF THE FIRE PRECAUTIONS ACT.

IN PARTICULAR THEY SHOULD BE AWARE OF THE NEED FOR REGULAR SERVICING BY A COMPETENT

PERSON TO ENSURE CONTINUED SAFE AND EFFICIENT APPLIANCE PERFORMANCE.

WARNING:   TO PREVENT SHOCKS, APPLIANCES WHETHER GAS OR ELECTRIC, MUST BE EARTHED.

UPON COMPLETION OF INSTALLATION, THE OWNERS MANUAL SHOULD BE HANDED TO USERS AND

THE INSTALLER SHOULD INSTRUCT RESPONSIBLE PERSON(S) IN THE CORRECT OPERATION AND

MAINTENANCE OF THE APPLIANCE.

THIS EQUIPMENT IS ONLY FOR PROFESSIONAL USE, AND SHALL BE OPERATED BY QUALIFIED

PERSONS. IT IS THE RESPONSIBILITY OF THE SUPERVISOR OR EQUIVALENT TO ENSURE THAT USERS

WEAR PROTECTIVE CLOTHING, AND TO DRAW ATTENTION TO THE FACT THAT, SOME PARTS WILL, BY

NECESSITY, BECOME VERY HOT AND WILL CAUSE BURNS IF TOUCHED ACCIDENTALLY.

UNLESS OTHERWISE STATED, PARTS WHICH HAVE BEEN PROTECTED BY THE MANUFACTURER ARE

NOT TO BE ADJUSTED BY THE INSTALLER.

BEFORE ATTEMPTING ANY SERVICING, ENSURE THAT THE ELECTRICAL SUPPLY IS DISCONNECTED.

WARNING:   THE UNIT MUST BE INSTALLED BY PERSONNEL QUALIFIED TO WORK WITH ELECTRICITY. 

IMPROPER INSTALLATION CAN RESULT IN INJURY TO PERSONNEL AND/OR DAMAGE TO 

EQUIPMENT. THE UNIT MUST BE INSTALLED IN ACCORDANCE WITH APPLICABLE CODES.

CAUTION:   SHIPPING STRAPS ARE UNDER TENSION AND CAN SNAP BACK WHEN CUT.

WARNING:  TO AVOID DAMAGE OR INJURY, FOLLOW THE WIRING DIAGRAM EXACTLY WHEN CONNECTING A 

UNIT.

WARNING:   BEFORE CLEANING THE OUTSIDE OF THE KETTLE, DISCONNECT ELECTRIC POWER . KEEP 

WATER AND SOLUTIONS OUT OF CONTROLS AND ELECTRICAL COMPONENTS.

NOTICE:  

DO NOT USE ANY DE-GREASER THAT CONTAINS POTASSIUM HYDROXIDE OR SODIUM 

HYDROXIDE OR THAT IS ALKALINE.

WARNING:   USE OF ANY REPLACEMENT PARTS OTHER THAN THOSE SUPPLIED BY GROEN OR 

THEIR AUTHORIZED DISTRIBUTOR VOIDS ALL WARRANTIES AND CAN RESULT IN BODILY 

INJURY TO THE OPERATOR AND DAMAGE THE EQUIPMENT. SERVICE BY OTHER THAN 

FACTORYAUTHORIZED PERSONNEL WILL VOID ALL WARRANTIES.

WARNING:   HIGH VOLTAGE EXISTS INSIDE CONTROL COMPARTMENTS. DISCONNECT FROM BRANCH 

BEFORE SERVICING. FAILURE TO DO SO CAN RESULT IN SERIOUS INJURY OR DEATH.

Summary of Contents for DEE-CE Series

























Reviews: