manualshive.com logo in svg

Grizzly T1244, Owner'S Manual

Share
Download
Grizzly T1244 Owner'S Manual Download Page 23

Model T1244 (Mfd. Since 10/17)

-21-

Edge Jointing

Jointing  the  edge  of  a  board  involves  using  a 
straight cutting router bit to remove wood from the 
face of the board. The result is a perfectly flat and 
square edge.

To joint edge of a workpiece:

1.  DISCONNECT ROUTER FROM POWER!

2.  Secure straight cutting bit into router accord-

ing to router manufacturer's instructions.

3.  Install  smallest  table  insert  into  mounting 

plate that still allows router bit to freely rotate.

4.  Raise bit to a height slightly more than that of 

workpiece, then rotate it by hand until cutting 
flute (cutting edge) is perpendicular to fence 
boards.

Workpiece

Feed Direction

Bit

Rotation

Always feed workpiece against router bit 

rotation direction, as illustrated below. 

Otherwise, workpiece could be aggressive-

ly pulled from your hands, drawing them 

into spinning cutter.

When  using  a  miter  gauge,  the  fence  assembly 
must  be  parallel  to  the  table  T-slot  for  safe  and 
accurate cutting results. Use a fine ruler to make 
the  distance  equal  between  the  fence  assembly 
and  the  T-slot  along  the  full  length  of  the  table 
(see 

Figure 34).

Kickback injury may occur if fence is not 

parallel with T-slot. When using a miter 

gauge with this router table, ALWAYS 

 

make sure fence assembly is parallel with 

table T-slot BEFORE beginning routing 

operations.

Figure 34. Adjusting fence parallel with table 

T-slot.

T-Slot

Fence 

Assembly

Fine Ruler

Squaring Fence 

& Table

Summary of Contents for T1244

































Reviews:

No comments

Brands by name

Popular brands

Load more brands