background image

-20-

G1021X2 & G1021Z (Mfd. Since 08/16)

8.  attach dust port to planer with (6) M6-1 x 12 

flange bolts (see 

figure 14).

figure 14. dust port installed.

x 6

Dust collection

this machine creates a lot of wood chips/

dust during operation. breathing airborne 

dust on a regular basis can result in perma-

nent respiratory illness. Reduce your risk 

by wearing a respirator and capturing the 

dust with a dust-collection system.

to connect the machine to a dust-collection sys-
tem,  fit  a  4"  dust  hose  over  the  dust  port,  and 
secure in place with a hose clamp (see 

figure 15). 

tug the hose to make sure it does not come off. 

Note:  A tight fit is necessary for proper 
performance.

figure 15. Example of dust hose connected to 

dust port.

Minimum cfM at Dust Port: 400 cfM
Do not confuse this CFM recommendation with 
the rating of the dust collector. To determine the 
CFM at the dust port, you must consider these 
variables: (1) CFM rating of the dust collector, 
(2) hose type and length between the dust col-
lector and the machine, (3) number of branches 
or wyes, and (4) amount of other open lines 
throughout the system. Explaining how to cal-
culate these variables is beyond the scope of 
this manual. Consult an expert or purchase a 
good dust-collection "how-to" book.

3.  using  a  straightedge  as  a  guide,  rotate  set 

screws  until  extension  tables  are  in  plane 
with  main  table,  then  fully  tighten  hex  bolts 
installed during 

Step 1 on Page 19.

 Note: 

Bed rollers will give you a false read-

ing with your straightedge if they are raised 
above table. Move them down or work around 
them when leveling extension wings (refer to 

Bed Roller Height on Page 27 for details).

4.  insert key into keyway on handwheel shaft on 

top of planer.

5.  line  up  notch  in  handwheel  bore  with  key, 

then slide handwheel onto shaft.

6.  Slide  loW/high  direction  label  onto 

handwheel shaft, and secure handwheel with 
10mm flat washer and M10-1.25 hex nut (see 

figure 13).

7.  thread  handwheel  handle  into  handwheel 

(see 

figure 13), and tighten with wrench.

figure 13. table elevation handwheel installed.

install handle 

here

loW/high 

direction label

x 1

Summary of Contents for G1021X2













































































Reviews: