Grizzly G0648 Owner'S Manual Download | Manualshive

Page: 20 / 56

background image

-18-

g0648 Welding Fume Extractor

5.

press the on/oFF button. the opErating

lEd will light, and the machine will start
momentarily.

6.

observe the digital display and make sure the

EXhauSting tiME and FiltEr rolling
tiME values are at your last setting, or at least
at the factory initial settings for EXhauSting
tiME, and for FiltEr rolling tiME.

7.

Begin welding, being sure to follow all safety

rules.

Note:

If the warning lamp/buzzer comes on,

it indicates that the rolling-type filter has run
out and it is time to replace the roll.

8.

When finished welding, press the on/oFF

button, and the machine will wind down
slowly until the fan stops.

Note:

After the machine has operated over

a minute and then shut down, the FILTER
CLEANING lamp will light indicating that as
soon as the fan completely stops the vibrat-
ing filter will operate in three short durations
approximately 3 seconds each.

9.

For additional cleaning, manually push and

hold the vibrating filter button for a few more
seconds to remove any caked-on material.

10.

Clean out both the slag and dust drawers.

11.

after welding, make it a habit to inspect under

the machine and your work area for anything
that could smolder and start a fire.

«
...
18
19
20
21
22
...
»

Summary of Contents for G0648

























































Reviews:

No comments

Related manuals for G0648

Brand: Danfoss Pages: 28

Brand: RED SHIELD Pages: 25

Brand: Uniden Pages: 16

Brand: Teac Pages: 60

Brand: Magic Sing Pages: 10

Brand: Q-See Pages: 10

Hydro-Guard HG-4

Brand: Mueller Pages: 8

Brand: Dahua Technology Pages: 15

Brand: Newco Pages: 32

Firebox III 700

Brand: Watchguard Pages: 20

Brand: S.E.M. Pages: 6

Brand: BJ Live Pages: 2

Brand: Audiovox Pages: 15

L.O.C.PRO LPGL-2

Brand: PAC Pages: 2

Brand: Miller Pages: 56

PROGYS CEL 250 TRI

Brand: GYS Pages: 43

WeldForce WF-205MST

Brand: Weldclass Pages: 80

Brand: Pro Spot Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands