Grizzly G0634Z insert, Manual

Page: 88 / 92

-74-
Model G0634Z/G0634XP (Mfd. Since 01/20)
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.
Labels & Cosmetics
REF PART # DESCRIPTION REF PART # DESCRIPTION
800 P0634Z800 READ MANUAL LABEL 808 P0634XP808 TOUCH-UP PAINT, PB WHITE (G0634XP)
801 P0634Z801 RESPIRATOR/GLASSES LABEL 809 P0634Z809 ELECTRICITY LABEL
802 P0634Z802 MACHINE ID LABEL (G0634Z) 810 P0634Z810 MODEL NUMBER LABEL (G0634Z)
802 P0634XP802 MACHINE ID LABEL (G0634XP) 810 P0634XP810 MODEL NUMBER LABEL (G0634XP)
803 P0634Z803 CUTTERHEAD WARNING LABEL 811 P0634Z811 TABLE LOCK KNOB NOTICE (G0634Z)
804 P0634Z804 EAR PROTECTION LABEL 811 P0634XP811 POLAR BEAR LOGO 2-1/2 X 9-1/2 (G0634XP)
805 P0634Z805 DISCONNECT POWER LABEL 812 P0634Z812 CHANGE LEVER LABEL
806 P0634Z806 CHANGING OPERATIONS WARNING LABEL 813 P0634Z813 GRIZZLY NAMEPLATE-SMALL
807 P0634Z807 TOUCH UP PAINT, GRIZZLY GREEN 814 P0634XP814 TABLE LOCK KNOB NOTICE (G0634XP)
808 P0634Z808 TOUCH UP PAINT, GREY PUTTY (G0634Z)
G0634Z
G0634XP
DISCONNECT
POWER BEFORE
ADJUSTMENTS,
MAINTENANCE, OR
SERVICE.
HEARING LOSS
HAZARD!
Always wear hearing
protection when
using this machine!
Specifications
Motor: 5 HP, 220V, Single-Phase, 60 Hz
Full-Load Current Rating: 25A
Cutterhead: Spiral w/Carbide Cutters
Number of Spiral Rows/Inserts: 4/32
Replacement Inserts T24736 (10 Pack)
Indexable Cutter Size: 15 x 15 x 2.5mm
Cutterhead Speed: 5034 RPM
Cuts Per Minute: 20,136
Max. Width of Cut: 12 in.
Max. Depth of Cut: 1/8 in.
Min. Stock Length: 14 in.
Weight: 610 lbs. To reduce risk of serious personal injury when using this machine:
1. Read and understand owner’s manual before operating.
2. Always wear approved eye protection and respirator.
3. Disconnect power before changing blades, removing
parts, or doing maintenance, service, or adjustments.
4. Only plug power cord into a grounded outlet.
5. Do not wear loose clothing, gloves, jewelry, or other
items that can get entangled in moving parts. Tie back
long hair and roll up long sleeves.
6. Ensure machine is correctly set up before starting.
7. Do not plane two boards of varying thickness at the
same time.
8. Never cut deeper than 1/8" on a single pass.
9. Never joint material smaller than 14" long, 3/4" wide, or
1/4" thick when edge jointing, or 1/2" thick when face
planing.
10. Keep all guards in place and in proper operating
condition.
11. Make certain machine rests firmly on flat, level ground.
12. Do not allow hands or clothing to get pulled into
cutting area while feeding workpiece.
13. Be aware of "kickback" hazards and how to prevent
them.
14. Stand clear of board ends while planing.
15. Do not plane or joint boards with cracks, loose
knots, or other defects.
16. Always use push blocks when face planing.
17. Keep hands at least 4" away from cutterhead when
jointing.
18. Never reach into planer cutting area while machine is
running.
19. Do not operate when tired or under influence of drugs
or alcohol.
20. Do not expose to rain or use in wet locations.
21. Prevent unauthorized use by children or untrained
users; restrict access or disable machine when
unattended.
MODEL G0634XP
POLAR BEAR SERIES JOINTER/PLANER
COMBINATION MACHINE w/SPIRAL CUTTERHEAD
Mfd. for Grizzly in Taiwan
Date
S/N
WARNING!
806
806
805
808
807
804
809
810
813
802
800
811(G0634XP)
801 803
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual, call
(800) 523-4777 or go to
www.grizzly.com.
EYE/LUNG INJURY
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine.
DANGER!
Use this guard for all
operations possible, and
immediately reinstall it
following operations that
require its removal.
ROTATING
CUTTERHEAD BELOW!
KICKBACK HAZARD!
1. Ensure outfeed table is
even with knives.
2. Never exceed the
maximum depth of cut.
3. Do not stand directly
behind workpiece.
ALWAYS USE
PUSH BLOCKS!
Push blocks minimize the
possibility of operator’s
hands contacting the
cutterhead while cutting.
811(G0634Z)
814(G0634XP)
NOTICE
TO PREVENT DAMAGE TO
LOCKING MECHANISM, RELEASE
TABLE LOCK KNOB BEFORE
LOWERING TABLE.
812
NOTICE
Leaving the change lever
up for extended periods
may damage internal
components. Keep the
change lever down,
unless you are actively
planing workpieces.