18
– Blades fault
– Check that the blades are correctly mounted
– Sharpen or change the blades
– Adjust the tension of the cutting deck engine belt
Vibrations during operation
– Blades unbalanced
– Balance blades or replace if damaged
– Fastenings are loose
–
&KHFNDQGIDVWHQWKHEODGHÀ[LQJVFUHZVDQGWKH
À[LQJVFUHZVRIWKHHQJLQHDQGFKDVVLV
Incorrect PTO engagement
– When the PTO button is pressed, the blade
– Check the battery voltage, it must be at least
does not engage
12,5 V
– Check the levelness of the blade brake and the
electromagnetic clutch, 0.3 mm.
ELECTRICAL SYSTEM
The electrical system is protected by a fuse which cuts out the entire electrical system if blown.
$IWHUÀQGLQJDQGUHSDLULQJWKHIDXOW
replace the fuse with another of the same rating.
Never replace the fuse with one of a different rating.
The electrical system fuses are underneath the tank (Fig. 19).
If the problems persist after all the procedures described above have been carried out, contact the
Authorised After-Sales Service Centre.
1HYHU DWWHPSW WR PDNH GLIÀFXOW UHSDLUV XQOHVV \RX KDYH WKH QHFHVVDU\ HTXLSPHQW DQG WHFKQLFDO
expertise.
IMPORTANT!
– Take care not to reverse the battery polarity.
– Never operate the mower without the battery, since it is equipped with a charge regulator.
– Take care not to cause short-circuits.
IF THE MACHINE DOES NOT REMAIN IN NEUTRAL
Adjust the zero return device by tightening or loosening it (Fig. 17).
To adjust the forward and reverse travel speeds, use the screws Fig. 18.
ENDING WORK
After mowing, disengage the blades and drive back to base with the cutting deck in the highest
position.
To stop, move the travel lever to the STOP position (2, Fig. 1/B), set the throttle lever on the minimum
rpm, switch off the engine by turning the key toward the right (1, Fig. 7) and lower the deck to the lowest
position, engage the parking brake (Fig. 23 n. 2).
CLEANING
Clean the outside of the mower after each use.
STORAGE AND PROLONGED PERIODS OF DISUSE
Store the mower in a dry place, away from atmospheric agents, and preferably cover with a sheet.
If the mower is not going to be used for a long period (over 1 month), disconnect the red battery cable
and follow the instructions given in the engine manual. Also lubricate all of the articulated joints.
Regularly check that the battery voltage does not drop below 12,5 volts. If it does, recharge the battery.
Summary of Contents for CLIMBER CL9.16
