Grifco Fire Shutter Instruction Manual Download Page 10

Page: 10 / 16

REVERSING STARTERS AND OVERLOADS

Electronic Logic Controllers

For reversing starter connection details:

Refer to the diagram included with the control

INSTALLATION

GLMe2

415V Three Ø Motor
240V Single Ø 3 wire Motor
240V Single Ø 4 wire Motor

GLMe2N

415V Three Ø Motor

GLMe2L

415V Three Ø Motor
240V Single Ø 3 wire Motor
240V Single Ø 4 wire Motor

GLMe2NL

415V Three Ø Motor

3 Phase

RG374-LB3E007
415V Three Ø Motor, 240V Control Circuit, 2.3A - 3.2A Three Ø Amperage Overload

RG374-LB3E007-EX
415V Three Ø Motor, 240V Control Circuit, 2.3A - 3.2A Three Ø Amperage Overload

3 Phase No-
Neutral

RG378-LB3E007
415V Three Ø Motor, 240V Control Circuit, 2.3A - 3.2A Three Ø Amperage Overload

Single Phase

RG376-LB1E009
240V Single Ø Motor, 240V Control Circuit, 4 Wire, 4.5A - 6.3A Single Ø Amperage Overload

Summary of Contents for Fire Shutter

















Search results

Summary of Contents for Fire Shutter

Reviews:

Related manuals for Fire Shutter

Brands by name

Popular brands

Grifco Fire Shutter, Instruction Manual

Search results

Summary of Contents for Fire Shutter

Reviews:

Related manuals for Fire Shutter

Brands by name

Popular brands