Grifco Fire Shutter Instruction Manual Download Page 6 | Manualshive

Page: 6 / 16

background image

6

INSTALLATION

Mounting the Unit

The Fire Shutter is typically flag mounted below the door drum so that the opener shaft points toward the door opening and lies

beneath the sprocket of the door drum. For mounting you will need to either secure the opener to the roller shutter head plate
with prepared holes or slots, or use a mounting plate that will need fixing via a wall angle or similar existing fixture.

Note: THE FIRE SHUTTER IS NOT DESIGNED TO BE INSTALLED UPSIDE DOWN.
THE CHAIN GUIDE MUST NOT BE REPOSITIONED.

When assessing and selecting an appropriate mounting location, the following considerations should be made:

The unit must be mounted accurately so that the drive sprocket lines up with the shutter platewheel. There is only a small
allowance for adjustment of the drive sprocket position on the output shaft. Fit the correct length of drive chain around the drive
sprocket and platewheel.

«
...
4
5
6
7
8
...
»

Summary of Contents for Fire Shutter

















Reviews:

No comments

Related manuals for Fire Shutter

Brand: Warner Electric Pages: 3

Brand: iCeeO2 Pages: 7

Brand: SABAF Pages: 6

Brand: 1Control Pages: 8

Brand: Bard Pages: 8

Brand: Bardiani Valvole Pages: 35

Brand: Samson Pages: 40

Brand: tams elektronik Pages: 12

phyCORE-MCF548x

Brand: Phytec Pages: 104

Z1000 CIMR-ZU*A Series

Brand: YASKAWA Pages: 340

Brand: ETC Pages: 8

Brand: Mitsubishi Pages: 30

Brand: W.E.ST. Pages: 34

Brand: Ltech Pages: 4

Brand: Motor Guard Pages: 2

Brand: K&K Pages: 6

Brand: Rain Bird Pages: 11

LOOPDRIVE FIM-RC

Brand: 4EVAC Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands