background image

T02.0.3X.6C-07 

Mounting and operating manual OXY 3610 MP

  

Page 14 von 14 

 

GHM GROUP 

– Greisinger  |  GHM Messtechnik GmbH 

Hans-Sachs-Str. 26  |  93128 Regenstauf  |  GERMANY  
Phone +49 9402 9383-0  |  Fax +49 9402 9383-33 

www.greisinger.de

  |  

[email protected]

e

 

 
 

 

Storage temperature 

-20 ... 70 °C (electrode 0 ... 60 °C) 

Housing 

ABS (IP65 - with the exception of electrode and temperature probe con-
nection sockets)

 

Dimensions 

82 x 80 x 55 mm (without elbow-type plug and sensor sockets)

 

Mounting 

With fixing holes for wall mounting (in housing - accessible after cover 
has been removed). 

Mounting distance 

50 x 70mm, max. shaft diameter of mounting screws is 4 mm

 

Electric connection 

Elbow-type plug conforming to DIN 43650 (IP65), 
Max. wired cross-section 1.5 mm², cable diameter 4.5 to 7 mm. 

Directives / standards 

The device confirm to following European directives: 
2014/30/EU 

EMC directive 

2011/65/EU 

RoHS 

Applied harmonized standards 
EN 61326-1 : 2013 

Emission level: Class B 
EMI immunity according to table 1 
Additional error: <1% 

 

 

Summary of Contents for OXY 3610 MP















Reviews: