• Never leave this appliance within reach of children.
• Children of less than 3 years should be kept away unless continuously supervised.
• Do not immerse the appliance or its cord in water or any other liquids.
• Do not leave the appliance unattended during use.
• Do not leave the appliance unattended whilst connected to the mains supply.
• Always use this appliance on a solid, level, surface. • Do not use this appliance outdoors.
• It is imperative to unplug the power cord after the appliance has been used, before
it is cleaned and whilst being repaired. • Repairs to electrical appliances should only
be performed by a qualified electrician. Improper repairs may place user at serious risk.
• Do not operate this appliance with a damaged plug or cord, after a malfunction or after being
dropped or damaged in any way. • Regular, periodic checks should be carried out on the mains
cable to ensure no damage is evident. Should there be any signs of damage the appliance
should not be used. • If the power cable is damaged, it should only be replaced by the manufac
-
turer or a suitable qualified after-sales-service in order to avoid a hazard.
• Do not allow the mains cable to hang over sharp edges or come in contact with hot surfaces.
• Do not run the mains cable under carpets, rugs, etc. • This appliance is intended for household
use only and should not be used for industrial purposes. • Do not use any accessories or attach
-
ments with this appliance other than those supplied or recommended by the supplier.
• Do not use this appliance for anything other than its intended use. • Do not push objects
(including fingers) into the fan grill or any openings as this could risk injury, damage to the
appliance and/or electric shock. • Unplug after each use. Grasp the plug, not the cord.
01.
02.
03.
04.
05.
06.
07.
10.
12.
08.
09.
11.
13.
EN I Floor Fan GB560
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety
precautions should always be followed.
These instructions should be saved for future
reference:
• Read and familiarise yourself with all operating
instructions before using this Pedestal Fan.
• Before plugging your unit into the mains, visually
check that the unit is intact and has not suffered any
transit damage. • Do not use this product with
a programmer, timer, separate remote-control system
or any other device.
• Check that the voltage indicated on the data plate
corresponds with that of the local network before
connecting the appliance to the mains power supply.
• This appliance can be used by children aged from
8 years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and user mainte
-
nance shall not be made by children without supervi
-
sion. • Close supervision is required when using this
appliance near children.
Description of parts:
1. Front Guard 2. Guard Nut and Screw 3. Fan Blade 4. Rear Guard Central Fixing Nut
5. Rear Guard 6. Speed Control Switches 7. Motor Housing 8. Oscillation Control
9. Motor Spindle 10. Blade Retaining Nut 11. Pivot Screw 12. Pole Retaining Screw
13. Adjustable Pole 14. Pole Clamp 15. Lower Base Pole 16. Screw Cover
17. Base Fixing Screws 18. Base 19. Base End Caps
Assembly:
1.
Take the two base cross members (18) and push the 4 base end caps (19)
into the ends if not already fitted and then cross them over together.
2.
Remove the four screws from the two base members and attach the lower base pole (15) to
the base using a pozidrive screwdriver (not supplied).
3.
Unscrew and remove the pole clamp (14 – shown in step 2 above) and slide the screw cover
(16) down over the adjustable and lower base pole (13 & 15) until it is in place over the screws.
4.
Replace the pole clamp (14) and at the same time raise the chrome adjustable pole (13) then
tighten the clamp (14). Attach the fan assembly on top of the pole and tighten the pole retaining
screw (12).
NB the adjustable pole (13) can sometimes slip inside the lower base pole (15) during transit.
5.
Note the Rear Guard locating pins on the Motor Housing (7). (Guard locating pins)
6.
Place the rear guard (5) over the pins on the motor housing (7) and replace the Rear Guard
Central Fixing (4) nut by screwing it back on clockwise. NB the carry handle is at the top.
7.
Take the fan blade (3) and slide it onto the motor spindle (9) ensuring that notches on the rear
of the fan blade line up with the splines on the spindle. NB Rear Guard removed for clarity.
8.
Secure the fan blade to the motor spindle by screwing on the Blade Retaining Nut (10) in an
anticlockwise direction. NB the retaining nut is reverse threaded.
9.
Remove the small Guard Nut & Screw (2) from the front guard (1).
10.
Move the clips around the outside edge of the front guard outwards.
11.
Hang the front guard (1) over the top of the rear guard (5).
12.
Bring the front guard down to meet the rear guard and push the clips inwards
until the front guard is fastened to the rear guard.
13.
Finally fit the Guard nut and screw
(arrowed) through the holes in the bottom edge of the guards and tighten with a suitable
pozidrive screwdriver (not supplied). NB this screw and nut must be fitted so that the guard
cannot be removed
Operating instructions:
Place the fan in the desired position ensuring that it is level and stable.
If desired, the fan guard can be tilted up and down to alter the direction of the airflow.
NB. do not adjust the fan whilst connected to the mains and/or switched on.
Slacken the Pole Clamp (14) and adjust the fan to the desired height using the Adjustable Pole
(13), tighten the pole clamp once the desired height is set.
NB. the adjustable pole (13) can sometimes slip inside the lower base pole (15) during transit.
Press the ‘0’ button on the pedestal to ensure the fan is off. Insert the mains plug into the nearest
socket. • Press the 1 button for the low speed. • Press the 2 button for the medium speed • Press
the 3 button for the high speed NB. Press the ‘0’ button to switch the fan off.
Making Your Fan Oscillate From Side To Side:
Press the oscillation control (8) down to enable
the fan to oscillate from side to side. Pull the control up to stop the fan oscillating.
Care and Use of your Fan
• Ensure that the fan is not connected to the mains supply before
cleaning. • Wipe the fan body clean with a clean, soft damp cloth.
• Do not immerse the fan or its cord in water or any other liquid.
Technical Data:
Voltage : 220-240V AC 50-60Hz Rated power : 40W
