background image

I FEEL


NOTE

CLOCK

SLEEP

Press this button, can select Sleep 1 (     1),

Sleep 2 (      2), Sleep 3 (      3) and cancel the

Sleep, circulate between these, after electrified, 

Sleep Cancel is defaulted.

Sleep 1 is Sleep mode 1, in Cool modes; sleep

 

Clock time adopts 24-hour mode.

 

The interval between two operations can

'

t exceed 5s. 

Otherwise, remote controller will quit setting status. 
Operation for TIMER ON/TIMER OFF is the same.

9

status after run for one hour, the main unit setting 

temperature will increase 1 , two hours, setting 

temperature increased 2

, then the unit will run at

this setting temperature; In Heat mode: sleep 

Press this button to set clock time. "      " icon on 

remote  controller  will  blink.  Press  " "  or  " " 

button within 5s to set clock time. Each pressing of 

" "  or  " "  button,  clock  time  will  increas  e  or 

decrease  1  min.  If  hold  " "  or  " "  button  ,  2s 

later,  time  will  change  quickly.  Release  this  button 

when  reaching  your  required  time.  Press  "CLOCK" 

button to confirm the time. "     " icon stops blink-

ing.

status after run for one hour, the setting tempera- 

ture will decrease 1 , two hours, setting tempera-

ture will decrease 2 , then the unit will run at this 

setting temperature.

Sleep 2 is sleep mode 2, that is air conditioner

will run according to the presetting a group of

sleep temperature curve.

Sleep 3-the sleep curve setting under Sleep

mode by DIY;

(1)Under Sleep 3 mode, press “TURBO” button for a

long time, remote controller enters into user indi-

viduation sleep setting status, at this time, the time

of remote controller will display “1hour”, the setting

temperature “88” will display the corresponding

temperature of last setting sleep curve and blink

(The first entering will display according to the

NOTE

Under on and off status, you can set T-OFF or T-ON 

 

simultaneously. 

Before setting T-ON or T-OFF, please adjust the 

clock time.

After starting up T-ON or T-OFF,set the constant 

circulating valid.

After that, air conditioner will be turned on or turned 

off according to setting time. ON/OFF button has no 

effect on setting. If you don’ t need this function, 

please use remote controller to cancel it.

initial curve setting value of original factory);

(2)Adjust “

” and “

” button, could change the

corresponding setting temperature, after adjusted,

press “TURBO” button for confirmation;

(3) At this time, 1hour will be automatically

increased at the timer position on the remote con-

trol, (that are "2hours" or "3hours" or "8hours"), the

place of setting temperature "88" will display the

corresponding temperature of last setting sleep

curve and blink;

(4) Repeat the above step (2)~(3) operation, until

8 hours temperature setting finished, sleep,curve

setting finished, at this time, the remote controller

will resume the original timer display; temperature

display will resume to original setting temperature.

Sleep3- the sleep curve setting under Sleep

mode by DIY could be inquired:

The user could accord to sleep curve setting

method to inquire the presetting sleep curve, enter

into user individuation sleep setting status, but do

not change the temperature, press "TURBO" button

directly for confirmation. Note: In the above preset-

ting or enquiry procedure, if continuously within

10s, there is no button pressed, the sleep curve

setting within 10s, there is no button pressed, the

sleep curve setting status will be automatically quit

and resume to display the original displaying. In

the presetting or enquiry procedure, press

"ON/OFF" button, "MODE" button, "SLEEP" button,

the sleep curve setting or enquiry status will quit

similarly.

Press this button to start I FEEL function and "      " 

will be displayed on the remote controller. After this

function is set, the remote controller will send the 

detected ambient temperature to the controller 

and the unit will automatically adjust the indoor te-

mperature according to the detected temperatu

 

re. 

Press this button again to cancel I FEEL function 

and "      " will disappear. 

Please put the remote controller near user when

 

 this

function is set. Do not put the remote contro

 

ller 

near the object of high temperature or low temper-

ature in order to avoid detecting inaccurate am

 

bie-

nt temperature.When I FEEL function is turned on, 

the remote controller should be put within the a

 

rea 

where indoor unit can receive the signal sent by

 

 

 the 

remote controller. 

Summary of Contents for Vireo Gen 3 3VIR09HP115V1AH





























Reviews: