background image

11

1. 

2. 

3. 

4. 

Reinstall the cover (as shown in Fig 2

).

Fig.1

Replacement of batteries in 

remote controller

Fig.2 

Lift the cover along the direction of arrow 

(as shown in Fig 1

).

Place two 7# (AAA 1.5V) dry batteries, and make 

sure the position of “ + ” polar and “ - ” polar is 

correct (as shown in Fig 2

).

Take out the original batteries (as shown in 

Fig 1

).

Child lock function

Temperature display switchover function

Press "MODE" and "SLEEP" buttons simultaneou-

sly to start      function

Under OFF status, press " " and "MODE" buttons 

simultaneously to switch temperature display 

between 

 and 

.  

Auto clean function

 

During operation, poin t the remote control signal 
sender at the receiving window on indoor unit.

 

The distance between signal sender and receiving 
window should be no more than 8m, and there 

should be no obstacles between them.

 

Signal may be interfered easily in the room where 
there is 

uorescent lamp or wireless telephone; 

remote controller should be close to indoor unit 
during operation.

 

Replace new batteries o f the same model when 
replacement is required.

 

When you don

'

t use remote controller for a long time, 

please take out the batteries.

 

If the display on remote controller is fuzzy or there

'

no display, please replace batteries.

Press " " and " " simultaneously to turn on or 

turn off child lock function. When child lock func-

tion is on, "    " icon is displayed on remote control-

ler. If you operate the remote controller, the "    " 

icon will blink three times without sending signal to 

the unit.

This function is only available for some models.

Under unit off status, hold "MODE" and "FAN" 

buttons simultaneously for 5s to turn on or turn off 

the auto clean function. When the auto clean func-

tion is turned on, indoor unit displays "CL" . During 

the auto clean process of evaporator, the unit will 

perform fast cooling or fast heating. There may be 

some noise, which is the sound of flowing liquid or 

thermal expansion or cold shrinkage. The air con-

ditioner may blow cool or warm air, which is a 

normal phenomenon. During cleaning process, 

please make sure the room is well ventilated to 

avoid affecting the comfort.

function

When the remote controller is turned off, power

limiting function is cancelled. If you want to acti-

vatethe function, please repress this button.

If the current power is lower than the maximum

power of        mode, then the power will not be 

limited after entering into such mode.
For the model with one outdoor unit and two indoor 

units, if any one of indoor units enters into power 

limiting function, the outdoor unit will enter into the 

set limiting power mode of indoor unit; when two 

indoor units enter into power limiting mode, then 

the power of outdoor unit will be limited according 

to the lower power of the two indoor units.

blank

No Setting

● 

● 

● 

        function is for limiting power of the whole unit.

Press this button, the remote controller will circu-

larly display as the following:

 

Maximum power limited under the     mode is lo-

    

wer than that of     mode.

 

If you want to cancel the power limiting function,

press the button      till the icon in remote contro-

ller is not displayed.

NOTE

NOTICE

 

The  auto clean function can only work under normal 

ambient temperature. If the room is dusty, clean it 

once a month; if not, clean it once every three 

months. After the auto clean function is turned on, 

you can leave the room. When auto clean is finished, 

the air conditioner will enter standby status.

NOTE

 

This function is only available for some models.

Summary of Contents for Vireo Gen 3 3VIR09HP115V1AH





























Reviews: