background image

4

Safety Considerations

1

Before  use,  please  read  the  Instructions  thoroughly  and  operate  the  machine  correctly 
according to the guideline herein. 

2

We require your special attention to the meaning of these two symbols: 

WARNING!: A symbol indicating that improper operation might cause human death or severe injury. 

CAUTION!: A symbol indicating that improper operation might cause human injury or damage. 

WARNING!

The  installation  work  shall  carried  out  by  franchise  repair  station.  Improper  installation  might  cause 
water leakage, electric shock or fire. 

Please  install  at  a  place  adequately  strong  to  support  the  weight  of  the  air  conditioner  unit.  If  the 
strength is low, the air conditioner might fall down and cause human injury or even death. 

To ensure correct drainage of water, the drainage pipe shall be installed according to the installation 
instructions. Also the heat insulation shall be provided to avoid condensing. Improper installation of the 
pipe might result in water leakage and lead to possible wetting of the articles in the room. 

Do not use or store flammable, explosive or poisonous substances beside the air conditioner. 

In  event  of  any  fault  (e.g.  smell  of  burn),  please  immediately  disconnect  the  mains  switch  of  the  air 
conditioner unit. 

Keep the air flowing to avoid oxygen deficiency in the room. 

Never put your fingers or insert any object into exhaust port or intake grill. 

Regularly check if the installation support is damaged after a long period of use. 

Never  make  any  modification.  To  repair  or  move  the  air  conditioner,  please  contact  the  vendor  or 
professional installation technicians. 

High  voltage  exists  in  outdoor  unit,  so  that  the  electric  box  can  only  be  removed  or  installed  by 
professional technicians. 

CAUTIONS!  

Before installation, please check if the power supply complies with the ratings on nameplate and check 
its safety. 

Before use, please check and confirm if the power cables, drainage pipes and pipelines are correctly 
connected, so as to avoid water leakage, refrigerant loss, electric shock or fire accidents. 

To ensure effective earthing of the air-conditioner unit and avoid electric shock, the main power must 
be securely earthed. Do not connect the earth wires to gas pipe, water pipe, lightning rod or telephone 
line. 

Once the air conditioner is started, let it run for 5 minutes at least before you can stop it; otherwise, the 
service life of the air conditioner will be affected. 

Do not allow the child to operate the air conditioner unit. 

Do not operate the air conditioner unit with wet hands. 

To clean the air conditioner or replace the air filter, please disconnect the unit from main power supply 
firstly. 

To put the air conditioner long out of use, please disconnect the main power supply. 

Do not expose the air conditioner unit directly to corrosive environment, e.g. water or moisture. 

Do not step on the air conditioner unit or put any substances on it. 

Summary of Contents for GMV-Pds100W/Na-K







































Reviews: