Gree GMV-Pds100W/Na-K Installation And Operating Instructions Manual Download | Manualshive

Page: 30 / 38

background image

30

Components and their Names

● System Schematics

Wall-mounted
indoor unit

Cassette Indoor Unit

Air-duct indoor unit
(Round air
discharge port)

Air-duct indoor unit
(Rectangular air
discharge port)

Outdoor Unit

Hydro-Box

Water
Tank

Fig. 24

The HOME-GMV system consists of outdoor unit ,Hydro-box and Max. 7 sets of indoor units. The indoor

unit may be ceiling mounted, wall mounted, air duct type, or low-pressure ultra-thin air duct type. The

ceiling-mounted and wall-mounted indoor unit is controlled by remote controlled, while the air duct type and

low-pressure ultra-thin air duct type indoor unit may controlled by remote controller and wired controller.

When any of the indoor units or the Hydro-box receives the run command, the outdoor unit will be started.

The outdoor unit is stopped when all the indoor units and Hydro-box are stopped.

«
...
28
29
30
31
32
...
»

Summary of Contents for GMV-Pds100W/Na-K







































Reviews:

No comments

Related manuals for GMV-Pds100W/Na-K

Brand: Badu Tec Pages: 98

Brand: Garden Oasis Pages: 12

Brand: laguna Pages: 24

Brand: VacPak-It Pages: 9

Brand: DAB Pages: 184

Brand: Raymarine Pages: 24

SunCentric Series

Brand: Dankoff Solar Pages: 11

Brand: A-Star Pages: 29

Brand: Dyna-Glo Pages: 60

Brand: Cozy Products Pages: 2

Brand: Salton Pages: 7

Brand: Greenway Home Products Pages: 9

Brand: Gorenje Tiki Pages: 48

Brand: Olimpia splendid Pages: 96

Brand: IWAKI PUMPS Pages: 32

Brand: Bravo Pages: 12

BASITRONIC CDX 11-U

Brand: clage Pages: 32

Brand: Dyna-Glo Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands