GREAT PLAINS 3S-3000 Series Original Instructions Manual Download Page 23

Page: 23 / 50

3S-3000

Table of Contents

Assembly

4/25/19

Table of Contents

195-144M

Open Center Conversion

If the drill was shipped with an Open Center kit, it is not
factory-installed. Install it now. An installation manual is
provided.

Point Row Option

If the Point Row Option was ordered with the drill, the
hydraulics and drill electrical lead are factory-installed.

If the customer’s primary tractor is available, install the
control module in the tractor cable and make the electrical
connection. Consult the Point Row installation manual
provided.

If the primary tractor is not available, temporarily connect
the control module so that openers can be operated
during Setup.

Post Assembly Checklist



Check that all working parts are moving freely, bolts
are tight, and cotter pins are spread.



Check for proper tension and alignment on all drive
chains.



Check that all safety decals and reflectors are located
correctly and are legible. Replace if improperly
located or damaged. Refer to “

Safety Decals

” in the

Operator’s manual.



Inflate tires to recommended pressures as listed on
the

“Tire Inflation Chart”

in the Operator’s Manual.

Tighten wheel bolts as specified on “

Torque Values

Chart

” on page 37.

Figure 20

Open Center Conversion

18750

Figure 21

Point-Row Connector

26469

Summary of Contents for 3S-3000 Series



















































Search results

Summary of Contents for 3S-3000 Series

Reviews:

Related manuals for 3S-3000 Series

Brands by name

Popular brands

GREAT PLAINS 3S-3000 Series, Original Instructions Manual

Search results

Summary of Contents for 3S-3000 Series

Reviews:

Related manuals for 3S-3000 Series

Brands by name

Popular brands