L-SOLUTION 700 / 800 / 900 machines
. 10
First contact
LASER safety
This LASER machine contains a sealed carbon dioxide (CO2) LASER that produces
intense and invisible LASER radiation at a wavelength of 10.6 microns (
µ
m)
(0.417 10
-6
inch) in the infrared spectrum.
This LASER system contains a CO2 LASER in a Class I enclosure. However, due to the
presence of a visible red LASER diode (power < 1mW), the entire LASER system is
classified as Class 2.
- The entire system is completely enclosed with a protective housing. This will completely contain the invisible C02 LASER
beam under normal use. However, the red diode LASER is a visible LASER beam.
DO NOT STARE INTO THE BEAM
OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.
- The user door(s) are safety interlocked and will disable the CO2 LASER beam from firing when the user door(s) are opened.
The red diode LASER beam is
NOT
safety interlocked and can be activated with the door(s) either open or closed.
Do not modify or disable any safety feature of this system. Do not operate any system
that has had its safety features modified, disabled, or removed.
Improprer use of controls and adjustments, or performance of procedures other than
those specified in this manual, may invalidate the safety of this system.
CDRH and EC regulations require all LASER manufacturers to affix warning labels in specific locations throughout the
equipment.
The following warning labels are placed on the LASER system for your safety. DO NOT
remove them for any reason. If the labels become damaged or have been removed for
any reason, DO NOT OPERATE the LASER system and immediately contact Gravograph
for a free replacement.
1 label
:
On the back of the system next to the serial number tag. Visible when viewing the LASER system from the backside.
This machine is in compliance with American 21 CFR standards,
subchapter J except for deviations pursuant to LASER notice N
°
50,
dated July 26, 2001.
2 labels
:
One is next to the beam window where the LASER beam enters the engraving area inside the LASER system and
is visible when the front door is opened.
The second one is located on the LASER source where the LASER beam comes out. It is not visible under normal
operating conditions.
AVOID EXPOSURE - Visible and invisible LASER radiation is emitted
from this aperture.
1 label
:
On the LASER tube assembly. Not visible under normal operating conditions.
CAUTION LASER RADIATION.
Avoid eye or skin exposure to direct or scattered radiation.
Class 4 LASER - CO
2
LASER - Wavelength : 10,6
µ
m (0.417 10
-6
inch)
- Max. output : 100W.
4 labels
:
One is next to the beam window where the LASER beam enters the engraving area inside the LASER system and
is visible when the front door is opened.
The second one is on the right, on the #1 mirror cover.
The third one is located on the LASER head next to the access hole of the #2 mirror.
The fourth one is located on the buse of the head.
DANGER - Invisible and visible LASER radiation is present at that
place. Avoid eye or skin exposure to direct or scattered radiation.
LASER safety
Summary of Contents for L-Solution 700
