background image

19

20

This  page  (left)  shows  the  charging  process  with  the  parameters 
and graph. Both the voltage and current will increase to the preset 
parameters. The preset current may be limited by the charge/dis-
charge capacity and the input voltage setup. The maximum charging 
process can operate with 400W. The max discharging process can 
operate with 60W.

Tapping the graph will access the data view page.
The operating data can be displayed.
Please refer to pages 27-29 for further information.

Tapping the part in the red circle (image to the left), the set cur-
rent    window will appear. The operating charge current can then 
be set.    Tapping the X button will cause the set current window 
to disappear.
This setup is applied to the charger during the charging process 
and the parameters are not stored in the memory.
 

Pressing the STOP button will cause a pop-up window to ap-
pear, asking whether to stop operating. Tapping the STOP or 
ESC buttons will cause the charger to either stop or continue 
with the charging process, respectively. 

   ◎ DISCHARGE PAGE

Tapping the DISCHARGE icon on the main page will access the discharge mode. The pro-

gramming setup and the page transition are the same as described for the CHARGE mode. 

On the main page, tap the DISCHARGE 

icon to start the discharge process.

This page shows discharge setup for selecting
LiPo, Lilon, LiFe, NiCd, NiMH, Pb batteries

Tapping the part in the red circle (image on the left) will 
activate the parameters (blue), allowing the values to be 
programmed into the data spots.

LiPo, LiIon, LiFe, NiCd, NiMH, Pb battery discharge modes

- Voltage 
- Current 

- Cut-Temp
 

- Max Capacity 

: Final discharge voltage for each cell can be programmed 
: Discharge current. - This parameter can be adjusted from 0.1 to 10 Amps, operating within 
the maximum value of 60W.
: Cut-off temperature. - With an optional temperature sensor, a safety cut-off temperature 
can  be  set,  allowing  the  charging  or  discharging  process  to  terminate  automatically  for 
battery temperatures exceeding the preset temperature.
: The maximum capacity setting is used to terminate a discharge at battery capaci-
ties exceeding a preset percentage value. Damaged, poorly balanced or improperly 
programmed battery parameters can result in an overdischarge.

USER NAME

Summary of Contents for Polaron EX

























Reviews: