GRAUPNER MX-10 HOTT Programming Manual Download Page 127

Page: 127 / 208

127

Program description: Trainer system

Trainer Mode

Connecting two transmitters for trainer mode operations

The

mx-10

HoTT transmitter can be combined by wi-

reless means to form a Trainer system. Here, the second
transmitter must not be the mx-10 HoTT also, every
other HoTT transmitter with the possibility of wireless
Trainer operation is suitable.

Therefore please read the

manual of your HoTT system!

Switching from the normal operating mode to the trans-
mitters teacher or student mode is done by the mode
switch on the left top side of the transmitter:

To change the mode, move the mode switch on the
transmitter in the desired position, press and hold the
BIND-button and then switch on the transmitter.

To display the selected mode ...

LED Status

Buzzer

Description

orange LED
on

Transmitter mode
„normal“, country
setting: general

orange LED
ﬂ ashes

beeping
twice after
switching on

Transmitter mode:
pupil

orange LED
ﬂ ashes twice

2x beeping
twice after
switching on

Transmitter mode:
teacher

See LED and buzzer signals on page 88.

Important Note:
The following description is based on the time of
printing this manual current version 1.00 of the
transmitter software, and is equally valid for all
previous Software versions. It can not be excluded
that after the next update, the following description
will not be correspondend with the functionality of
the HoTT Trainer system.

Teacher transmitter settings

mx-10

HoTT

The trainer model must be programmed completely,
i. e. with all its functions including trims and any mixer
functions in the

mx-10

HoTT Teacher transmitter.

This

means that it must be possible to control the trainer
model fully, without restriction, by the Teacher trans-
mitter.

But, at the conclusion of these preparations,

the trainer model must be bound to the Pupil trans-
mitter.

A detailed description of the binding process can

be found on page 106 and 109.

Note when using the

mx-10

HoTT as pupil transmitter:

the

mx-10

HoTT binding procedure can only be done

in „normal“ mode. Before using the transmitter in Pupil
mode, bind the receiver in mode „normal“, then switch to
the mode „pupil“. In addition, no mixer may be activated,
move the jumper in the middle position „NO MIX“, see
also page 105.
All ﬁ ve

transmitter control functions

of the Teacher trans-

mitter “T” can be transferred to the pupil transmitter “P”.
The stick mode of the pupils transmitter may deviate
from the teacher transmitter, because the stick mode
and mixers will be transfered from the teachers transmit-
ter. Therefore the teachers transmitter must be properly
programmed for the training model with all functions and
mixers.

After the pupils transmitter is bound to the trainer model,
set the

mx-10

HoTT in the teacher mode. To change

the mode, move the mode switch on the transmitter in
the „teacher“ position, press and hold the BIND-button
and then switch on the transmitter.

Now press the BIND-button of the puplis transmitter:

mx-10

HoTT: press and hold

In the following the student programming for the

mx-

12/16/20

HoTT is described. Please read also the

instructions for your remote control system!
Switch on the transmitter, and use the arrow buttons of
the left or right-hand four-way button to leaf through on
both transmitters to the “Trainer” menu point of the multi-
function menu. (The trainer model’s receiving system,
previously bound to the Pupil transmitter, does not need
to be switched on during the following procedure.):

ser vo set.
D/R expo
wing mixer

contr set.
phase trim
free mixer

ser vo disp

basic sett

fail-safe

telemetr y
info disp

teach/pupi

Press the central

SET

button of the right-hand four-way

button to open the following menu point:

TRAINER/Pupil