background image

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

 

We reserve the right to introduce modifications. Not liable for printing errors!               

11/2011

 

24 

 

reimbursement of costs relating to the defect (such as installation / removal costs) 
and compensation for consequent damages unless they are allowed by statute. This 
does not affect claims based on legal regulations, especially according to product 
liability law.  
 
Guarantee requirements 
 
The purchaser is required to make the guarantee claim in writing and must enclose 
original proof of purchase (such as invoice, receipt, delivery note) and this guarantee 
card. The defective goods must be sent to us at the purchaser's own cost, using the 
address stated above.  
The purchaser should state the material defect or manufacturing fault or the 
symptoms of the fault in as accurate a manner as possible so that we can check 
whether our guarantee obligation is applicable.  
The goods are transported from the consumer to us and from us to the consumer at 
the risk of the consumer. 
 
Duration of validity 
 
This declaration only applies to claims made to us during the claim period as stated 
in this declaration.  The claim period is 24 months from the date of purchase of the 
product by the consumer from a dealer in the Federal Republic of Germany (date of 
purchase). If a defect arises after the end of the claim period, or if the evidence or 
documents required according to this declaration in order to make the claim valid are 
not presented until after this period, then the consumer forfeits any rights or claims 
from this declaration.  

 

Limitation by lapse of time 
 
If we do not acknowledge the validity of a claim based on this declaration made 
within the claim period, all claims based on this declaration expire after six months 
from the time of claim, but not before the end of the claim period.   
 
Applicable law 
This declaration, and the claims, rights and obligations arising from it, are based 
exclusively on the applicable German Law, without the norms of international private 
law, and excluding UN retail law. 
 
The following items must be observed:
 

  Before you fly the model, check that the radio control system is working reliably, 

and that all connections are secure. 

  If you intend to use dry cells as a power supply, please note that they must never 

be recharged. Only rechargeable batteries can be re-charged. 

  The  batteries  must  be  charged,  and  the  range  of  the  radio  control  system  must 

have been checked.  In particular, the transmitter and receiver batteries must be 
charged before each take-off. 

Summary of Contents for JODEL ROBIN DR 400/180


























Reviews: