background image

GRAUPNER/SJ GmbH 73230 KIRCHHEIM/TECK GERMANY 

Subject to modification! No liability for printing errors! 

03/2018 

 

16

 - 

Assembly plan text 

1.  Centre of gravity 
2.  Fuselage side sight 
3.  Fuselage front sight 
4.  Room for receiver battery and HoTT receiver 
5.  V shape of the wing, 1:10 scale 
6.  Please note that some parts are not shown in the fuselage front sight. 
7.  Possible dimensional differences between the construction plan and the 

incisions in the wing nose and end edge are due to the unavoidable length 
expansion of the building plan caused by fluctuations in the humidity and 
ambient temperature. Please provide the dimensional differences if necessary.  

8.  Please note that the outer airfoil part, the typical "ear" or winglet for the 

AMIGO V, is folded into the drawing plane in the airfoil. Furthermore, the ribs 
(46 and 80) are shown vertically. 

 

Warranty conditions 

Graupner, Henriettenstrassee 96, 73230 Kirchheim/Teck grants from the date of 
purchase of this product for a period of 24 months. The warranty applies only to the 
material or operational defects already existing when you purchased the item. 
Damage due to misuse, wear, overloading, incorrect accessories or improper 
handling are excluded from the guarantee. The legal rights and claims are not 
affected by this guarantee. Please check exactly defects before a claim or send the 
product, because we have to ask you to pay shipping costs if the item is free from 
defects. 

The present construction or user manual is for informational purposes only and may 
be changed without prior notice. The current version can be found on the Internet at 

www.graupner.de 

on the relevant product page. In addition, the company 

Graupner

 

has no responsibility or liability for any errors or inaccuracies that may appear in 
construction or operation manuals.  

No liability can be accepted for printing errors. 

 

 

Summary of Contents for AMIGO V

















Reviews: