GRANULDISK Lean Wash Center X2 User Manual Download Page 12 | Manualshive

Page: 12 / 37

GRANULDISK Lean Wash Center X2 User Manual Download Page 12

1 General description and safety

1.2 Technical data

Ventilation requirements with

EcoExchanger

450 m³/h

Heat emitted to room (total/sensi-

ble/latent)

5,8 kW / 2,1 kW / 3,6 kW

Heat emitted to room with EcoEx-

changer (total/sensible/latent)

4,9 kW / 2,1 kW / 2,8 kW

Drainage

Drain hose Ø 28 mm - 1,5 m

Drain capacity requirement

50 l / min.

Drain water temperature

65 °C

Maximum lift height drain pump

800 mm

Drain pump

40 W

DETERGENT & RINSE AID

Liquid detergent and rinse aid dosing dispenser with peristaltic pumps

are integrated into X2 Lean Wash Center®
Prepared for dosing installation.

NOTE

X2 Lean Wash Center® must be installed according to na-

tional regulations. X2 Lean Wash Center® is supplied with a

2 metres long electric cable to be connected to an ap-

proved supply disconnecting device on the wall. The supply

disconnecting device is not included in the delivery.

* Not in use simultaneously
** For specific data regarding delivered units, please see rating plate
*** Factory settings. The settings can be changed according to the local

standards.
**** Do not clean the machine with high-pressure water.

12

Rev. 2022-04

«
...
10
11
12
13
14
...
»

Summary of Contents for Lean Wash Center X2






































Reviews:

No comments