Grandstream Networks GXP2130 Series Administration Manual Download

Page: 44 / 89

GXP2130/GXP2140/GXP2160
FIRMWARE VERSION 1.0.5.18

GXP2130/GXP2140/GXP2160
ADMINISTRATION GUIDE

Page 42 of 87

SETTINGS PAGE DEFINITIONS

Table 9: Settings Page Definitions

Settings



General Settings

Local RTP Port

This parameter defines the local RTP port used to listen and transmit. It

is the base RTP port for channel 0. When configured, channel 0 will use

this port _value for RTP; channel 1 will use por2 for RTP. Local

RTP port ranges from 1024 to 65400 and must be even. The default

value is 5004.

Use Random Port

When set to "Yes", this parameter will force random generation of both

the local SIP and RTP ports. This is usually necessary when multiple

phones are behind the same full cone NAT. The default setting is "Yes"

Note:

This parameter must be set to "No" for Direct IP Calling to work.

Keep-alive Interval

Specifies how often the phone sends a blank UDP packet to the SIP

server in order to keep the "ping hole" on the NAT router to open. The

default setting is 20 seconds. The valid range is from 10 to 160.

Use NAT IP

The NAT IP address used in SIP/SDP messages. This field is blank at

the default settings. It should ONLY be used if it's required by your ITSP.

STUN Server

The IP address or Domain name of the STUN server. STUN resolution

results are displayed in the STATUS page of the Web GUI. Only

non-symmetric NAT routers work with STUN.

Public Mode

Configures to turn on/off the public mode for hot desking feature. The
default setting is “No”.

Settings



Call Features

Off-hook Auto Dial

Configures a User ID/extension to dial automatically when the phone is

off hook. The phone will use the first account to dial out. The default

setting is "No".

Off-hook Timeout

If configured, when the phone is on hook, it will go off hook after the

timeout (in seconds). The default value is 30 seconds. The valid range is

from 10 to 60.

Bypass Dial Plan Through Call

History and Directories

Enable/Disable the dial plan check while dialing through the call history
and any phonebook directories. The default setting is “No”.

Disable Call Waiting

Disables the call waiting feature. The default setting is "No".

Disable Call Waiting Tone

Disables the call waiting tone when call waiting is on. The default setting

is "No".

Disable Busy Tone on Remote

Disconnect

Disable the busy tone heard in the handset when call is disconnected
remotely. The default setting is “No”.

Summary of Contents for GXP2130 Series


























































































Search results

Summary of Contents for GXP2130 Series

Reviews:

Related manuals for GXP2130 Series

Brands by name

Popular brands

Grandstream Networks GXP2130 Series, Administration Manual

Search results

Summary of Contents for GXP2130 Series

Reviews:

Related manuals for GXP2130 Series

Brands by name

Popular brands