Granby KHM-1/090 Installation, Operation And Service Manual Download Page 3

 

 

1.0  IMPORTANT SAFETY ADVICE 

 
 
 

Please  read  and  understand  this  manual  before  installing,  operating  or  servicing  the 
furnace.
    To  ensure  you  have  a  clear  understanding  of  the  operating  procedures  of  the 
appliance  please  take  the  time  to  read  the  IMPORTANT  SAFETY  ADVICE  section  of  this 
manual. 

 
 

WARNINGS 

 

NEVER burn garbage or paper in the unit. 
NEVER store combustible material around it. 
DO NOT attempt to start burner when excess oil has accumulated, when unit is full of vapour 
or when heat exchanger is very hot. 
DO NOT use gasoline, crankcase drainings or any oil containing gasoline. 

 
 

CAUTION 

 

DO  NOT  START  THE  BURNER  UNTIL  ALL  FITTINGS,  COVERS  AND  DOORS  ARE  IN 
PLACE.    DO  NOT  TAMPER  WITH  THE  FURNACE  OR  CONTROLS,  CALL  A  QUALIFIED 
BURNER  TECHNICIAN.    DO  NOT  STORE  OR  USE  GASOLINE  OR  OTHER  FLAMMABLE 
VAPOURS AND LIQUIDS IN THE VICINITY OF THIS UNIT OR ANY OTHER APPLIANCE. 

 
 

DANGER 

 

Do not use this furnace as a construction heater.  Use of this furnace as a construction 
heater exposes it to abnormal conditions, contaminated combustion air and lack of air 
filtering.    Failure  to  follow  this  warning  can  lead  to  premature  furnace  failure  which 
could result in a fire hazard and/or bodily harm and/or materials damages. 

 
 

IMPORTANT 

 

This  manual  contains  instructional  and  operational 
information  for  the  KHM  OIL-FIRED  FURNACE.  Read 
the  instructions  thoroughly  before  installing  furnace  or 
starting the burner.  Consult local authorities about your 
local  FIRE  SAFETY  REGULATIONS.    All  installations 
must  be  in  accordance  with  local  state  or  provincial 
codes.  Improper  installation  will  result  in  voiding  of 
warranty. 

 
 
 

Summary of Contents for KHM-1/090




































Reviews: