background image

4

307160

WARNING

FIRE AND EXPLOSION HAZARD

Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and re-
sult in a fire or explosion and serious injury.

D

Ground the equipment and the object being sprayed. Refer to 

Grounding

 on page 5.

D

If there is any static sparking or you feel an electric shock while using this equipment, 

stop spray-

ing/dispensing immediately.

 Do not use the equipment until you identify and correct the problem.

D

Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being sprayed/dispensed.

D

Keep the spray/dispense area free of debris, including solvent, rags, and gasoline.

D

Before operating this equipment, electrically disconnect all equipment in the spray/dispense area.

D

Before operating this equipment, extinguish all open flames or pilot lights in the spray/dispense
area.

D

Do not smoke in the spray/dispense area.

D

Do not turn on or off any light switch in the spray/dispense area while spraying/dispensing or while
operating if fumes are present.

D

Do not operate a gasoline engine in the spray/dispense area.

TOXIC FLUID HAZARD

Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.

D

Know the specific hazards of the fluid you are using.

D

Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.

D

Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer.

Summary of Contents for Viscount II 210313

















Reviews: