background image

3

307160

WARNING

INJECTION HAZARD

Spray from the gun/valve, leaks or ruptured components can inject fluid into your body and cause ex-
tremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can
also cause serious injury.

D

Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate medi-
cal attention.

D

Do not point the gun/valve at anyone or at any part of the body.

D

Do not put your hand or fingers over the spray tip/valve nozzle.

D

Do not stop or deflect leaks with your hand, body, glove or rag.

D

Do not “blow back” fluid; this is not an air spray system.

D

Always have the tip guard and the trigger guard on the gun/valve when spraying/dispensing.

D

Be sure the gun/valve trigger safety operates before spraying/dispensing.

D

Lock the gun/valve trigger safety when you stop spraying/dispensing.

D

Follow the 

Pressure Relief Procedure

 on page 8 if the spray tip clogs and before cleaning,

checking or servicing the equipment.

D

Tighten all fluid connections before operating the equipment.

D

Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately.
Permanently coupled hoses cannot be repaired; replace the entire hose.

MOVING PARTS HAZARD

Moving parts can pinch or amputate your fingers.

D

Keep clear of all moving parts when starting or operating the pump.

D

Before checking or servicing the equipment, follow the

 Pressure Relief Procedure

 on page 8 to

prevent the equipment from starting unexpectedly.

Summary of Contents for Viscount II 210313

















Reviews: