manualshive.com logo in svg

Graco PRO 3500WB, Manual

Share
Download
Graco PRO 3500WB Manual Download Page 8

 

INSTALLATION

Install the Interconnect Cables

1.

Connect the interconnect cable (406) between the
terminal block and voltage control. See Fig 6. Fasten
the cable in cable clamp to provide strain relief.

2.

Connect the voltage control ground cable (127) to
the strain relief/ground terminal.

3.

Connect the strain relief/ground terminal cable (X) to
a true earth ground.

4.

Connect the strain relief/ground terminal cable (W) to
the safety fence.

Install the Grounding Rod

Connect the grounding rod to the strain relief/ground ter-
minal. See Fig 6. Hook the grounding rod onto the fence
near the gate, as shown in Typical Installation.

Install the Fluid Supply Unit

1.

Place the fluid supply unit on the isolation stand. See
Fig 6.

2.

Connect the cable’s (405) c-clamp from the isolation
stand terminal block to a metal part of the fluid supply
unit.

Fig 6  

Isolation 
Stand

Voltage 
Control

Strain Relief/

Ground Terminal

Connect cable

223–529 (406)

between 

terminal

block & voltage control

Connect cable 223–548

(127) between 

voltage

control base-plate & strain

relief ground terminal

Connect cable 223–547

(X) between

 

strain relief/

ground terminal &

 true

earth ground (approx. 25 ft

(7.6 m) long)

Connect cable 223–539
(405) between 

terminal

block & metal part of fluid
supply unit

Fluid Supply Unit

Grounding Grate

Terminal Block

Isolation Stand

Voltage Control Cable

Fluid Supply

Cable

Electrically
Conductive
Gun Air 
Supply Hose

Grounding
Rod

Connect cable 223–685

(W) between

 

strain relief/

ground terminal & safety fence

(approx. 1 ft (0.3 m) long)

Cable Clamp

406

404

405

402

401

Summary of Contents for PRO 3500WB

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands