manualshive.com logo in svg

Graco PRO 3500WB, Manual

Share
Download
Graco PRO 3500WB Manual Download Page 40

 

FLUID HOSE ASSEMBLY PARTS DRAWING

301

302

305

307

308

306

309

310

REF 306

303

304

317

REF 306

REF 306

310

315

312

311

313

314

308

307

316

FLUID HOSE ASSEMBLY PARTS LIST

Fluid Hose Assemblies

100 psi (7 bar) MAXIMUM WORKING PRESSURE
0.25 in. (6.35 mm) ID; 3/8–18 nptf; PTFE 

Fluid Hose 

Assy. Part No.

Hose Length

223–192

25 ft (7.6 m)

223–193

36 ft. (11 m)

223–194

50 ft (15.3 m)

HOW TO ORDER REPLACEMENT PARTS

1. To be sure you receive the correct replacement parts, kits or

accessories, always give all of the information requested in the
chart below.

2. Check the parts list to identify the correct part number; do not use

the ref. no. when ordering.

3. Order all parts from your nearest Graco distributor.

6 digit

Part

Number

Qty

Part Description

REF 
NO.

PART NO. DESCRIPTION

QTY

301

186–052

INSERT, barbed

1

302

180–553

FITTING, male

1

303

107–305

O-RING; Viton

1

304

110–736

O-RING; Viton

1

305

107–208

NUT, ferrule

1

185–918

HOSE, fluid; 25 ft (7.6 m)
 Part No. 223–192 ONL

Y

1

306

185–919

HOSE, fluid; 36 ft (1 m)
 Part No. 223–193 ONL

Y

1

185–920

HOSE, fluid; 50 ft (15.3 m)
 Part No. 223–194 ONL

Y

1

REF 
NO.

PART NO. DESCRIPTION

QTY

307

185–549

FERRULE, hose

2

308

185–547

HOUSING, ferrule

2

309

185–566

BRACKET, fitting

1

310

185–548

NUT; 5/8–24 UNEF-2B

2

311

185–972

PLATE, fitting

1

312

185–971

PLATE, fitting

1

313

100–021

SCREW, hex; 1/4-20 UNC-2A x 1” 5

314

102–025

NUT, hex; 1/4-20

6

315

154–636

WASHER

1

316

107–048

CONNECTOR; 3/8-18 npt(f)

1

317

103–337

O-RING; Viton

1

Summary of Contents for PRO 3500WB

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands