manualshive.com logo in svg

Graco PRO 3500WB, Manual

Share
Download
Graco PRO 3500WB Manual Download Page 22

 

SPRAY GUN ELECTRICAL TESTS

The performance of the spray gun is directly affected by
the condition of the electrical components contained
inside the gun. The electrical tests below can be used to
determine the condition of the power supply (18) and the
resistor stud (22) as well as the continuity of the electrical
path between the components.

Use megohmmeter 218–979 (see ACCESSORIES) and
an applied voltage of 500 volts to complete these electri-
cal tests. Connect the leads as shown.

WARNING

To reduce the risk of sparking, which could cause
fire, explosion, or electric shock and result in seri-
ous bodily injury, DO NOT use the megohmmeter
in the hazardous area. Remove the gun from the
hazardous area before testing it.

Test Gun Resistance

Remove the air cap, nozzle, and resistor stud. See 

Air

Cap/Nozzle/Resistor Stud Replacement. Measure the
resistance between the metal contact pin (C) and the gun
air inlet fitting (17). See Fig 13.

The resistance should be between 157.5 to 192.5
megohms. If the resistance is outside the specified
range, go to the next test. If the resistance is correct, test
the resistor stud resistance as shown on page 23.

Test Power Supply Resistance

Remove the power cartridge from the gun handle (7).
See 

Power Cartridge Replacement

.

Remove the turbine alternator (37) from the power car-
tridge. See 

Turbine Alternator Removal.

Measure the resistance from the power supply’s ground
contact point (EE) to the contact spring (18c) on the other
end of the power supply. See Fig 14.

The resistance should be 157.5 to 192.5 megohms. If the
resistance is outside the specified range, the power sup-
ply is defective and must be replaced. If the resistance of
the power supply is correct, proceed to the next test.

If you still have problems, refer to the ELECTRICAL
TROUBLESHOOTING CHART for other possible
causes of poor performance, or contact the nearest
authorized service agency.

Fig 13  

KEY

A

Megohmmeter

C

Metal Contact

17

Air Fitting

Fig 14  

KEY

A

Megohmmeter

18

Power Supply

18c

Contact Spring

EE

Ground Contact Point

17

A

18c

18

EE

A

02250

C

Summary of Contents for PRO 3500WB

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands