manualshive.com logo in svg

Graco PRO 3500WB, Manual

Share
Download
Graco PRO 3500WB Manual Download Page 34

 

SPRAY GUN SERVICE NOTES

Air Cap

Nozzle

Resistor Stud

Tighten into nozzle

[10 in-lb (1.12 N

m)]

Lubricate 
O-Rings

Do not overtighten Packing Cartridge into gun barrel

Loosen slightly if Packing Rod jams

Set Packing for 
2 lb drag on shaft

Lubricate

Alternator

Power Supply

Adhesive side

Lubricate

Lubricate

Fan Air Valve
Apply PTFE paste

Install Flow Regulator with concave side
toward Valve (lettering should be visible
when assembled)

Tighten until gap

between Hex and Gun

Barrel is 1 to 2 mm

Thread to

shoulder

Install over
Valve Rod

Lubricate

Push Muffler in by 
installing Exhaust Adapter

Left hand thread
Apply high strength Loctite

Torque to 35 to 45 in-lbs
(4 to 5.1 N

m)

Left hand thread

Press Exhaust Tube
onto  Barb

Align Retaining Ring
holes with flat on 
Spacer to ease 
assembly/disassembly

CAUTION: To avoid dam-
aging gun, 

DO NOT over-

tighten screws. Tighten to
18 in-lbs (2 N

m) 

MAXI-

MUM (about half turn past
snug), using  wrench (63)
provided.
Capscrews

Lubricate

Hose Ferrule

Torque to

80 in-lbs

(9.1 N

m)

Will remain in

gun when hose

removed

Apply low strength 

(purple) Loctite or

equivalent to threads

Fan Air Valve
& Nozzle Wrench

Apply high strength
(green) Loctite

 to

thread. Assemble
flush with end of
screw.

WARNING: DO
NOT remove 
contact ring

Summary of Contents for PRO 3500WB

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands