Graco Pack n Play Series Owner'S Manual Download Page 10 | Manualshive

Page: 10 / 48

background image

Center of floor must be up.

1. Lift up slightly on the top rail.
2. Push in on the button located

on the side of the top rail to
release the two tubes.

3. Push down.

• If top rails do not unlatch,

DO

NOT FORCE

. Lift the center of

the floor higher.

•

Both

tubes must be released

for the top rail to fold.

11

«
...
8
9
10
11
12
...
»

Summary of Contents for Pack n Play Series

















































Reviews:

No comments

Related manuals for Pack n Play Series

Brand: Oasis Pages: 10

Brand: Baby Jogger Pages: 8

Transat Easy B012002

Brand: Badabulle Pages: 12

KUMO 010165 Series

Brand: Quax Pages: 14

Brand: maika Pages: 6

DRIFT GLIDING crib

Brand: Ickle Bubba Pages: 24

Brand: 4MOMS Pages: 23

Brand: Legacy Pages: 6

Brand: Northbeam Pages: 6

Brand: Fisher-Price Pages: 16

Brand: Fisher-Price Pages: 28

Brand: Fisher-Price Pages: 32

Brand: Polywood Pages: 2

Brand: Sunburst Pages: 4

Brand: Crate&Barrel Pages: 4

Brand: Burigotto Pages: 20

Brand: Fisher-Price Pages: 24

Brand: ubabub Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands