Graco Pack n Play Series Owner'S Manual Download Page 47

Page: 47 / 48

FROM TIME TO TIME CHECK YOUR PLAYARD

for worn parts, torn

material or stitching. Replace or repair the parts as needed. Use only

Graco

replacement parts.

IF PLAYARD IS USED AT THE BEACH

, you MUST clean sand off your

playard, including the feet, before packing it into cover. Sand in top rail

lock may damage it.

TO CLEAN PLAYARD

, use only household soap or detergent and

warm water.

TO WASH CARRY BAG

, machine wash in cold water on delicate cycle

and drip-dry. NO BLEACH.

TO WASH BASSINET:

Remove electronics module and vibration unit.

NEVER remove cord from bassinet. Hand wash with warm water and

household soap. Drip dry.

Care and Maintenance

TO WASH SEAT:

1. Remove vibration unit.
2. Remove small cord as shown below.

Machine wash in cold water on delicate cycle and drip-dry.

NO BLEACH. Refer to your care tag on your seat pad for washing

instructions.

Summary of Contents for Pack n Play Series

















































Search results

Summary of Contents for Pack n Play Series

Reviews:

Related manuals for Pack n Play Series

Brands by name

Popular brands

Graco Pack n Play Series, Owner'S Manual

Search results

Summary of Contents for Pack n Play Series

Reviews:

Related manuals for Pack n Play Series

Brands by name

Popular brands