manualshive.com logo in svg

Graco LineLazer 3400, Operation - Repair - Parts, Page: 28 / 44

Share
Download
Graco LineLazer 3400 Operation - Repair - Parts Download Page 28

Pinion Assembly/Clutch Armature/Clamp 

28

3A4587B Operation, Repair, Parts

Clutch Armature

9. Use an impact wrench or wedge something 

between clutch armature (39) and clutch housing to 

hold engine shaft during removal.

10. Remove four screws (36) and lock washers (35).
11. Remove armature (39).

Installation

Clutch Armature

1. Lay two stacks of two dimes on smooth bench sur-

face.

2. Lay armature (39) on two stacks of dimes.
3. Press center of hub down to bench surface.

4. Install armature (39) on engine drive shaft.
5. Install four screws (36) and lock washers (35) with 

torque of 125 in-lb.

Pinion Assembly

6. Install o-ring (44e).
7. Tap pinion shaft (44c) in with plastic mallet.
8. Install retaining ring (44d) with beveled side facing 

up.

9. Place pinion assembly on bench with rotor side up.
10. Apply locktite to screws. Install four screws (42) and 

lock washers (35). Alternately torque screws to 125 

in-lb until rotor is secure. Use threaded holes to hold 

rotor.

11. Install pinion assembly (44) with four screws (18).
12. Connect clutch (

+

) and clutch (

–

) connectors to wire 

harness.

ti

55

33a

36

35

39

0

.12 +.

0

1 in. (3.

0

 +.2

5

 mm)

dimes

ti

55

34a

39

Summary of Contents for LineLazer 3400













































Reviews:

No comments