background image

Component Identification

3A2960A

3

Component Identification

Keypad, Display, and Icons

Pump ON LEDs (A, B, C)

A

Pressure Control LED: In RUN MODE illuminates 
indicating function mode that is currently running.

B

Cycle Control LED: In RUN MODE illuminates 
indicating function mode that is currently running.

C

Time Control LED: In RUN MODE illuminates 
indicating function mode that is currently running.

Pump OFF LED (D)

In RUN MODE this LED illuminates when in the 
OFF or RESET portion of the RUN CYCLE.

Display (E)

A blinking field on the display indicates the controller 
is in SETUP MODE.

In RUN MODE numbers on the display will not blink.

Alarm LED (F)

Illuminates when any alarm is detected. When an alarm 
is active an error code displays and an audible alarm 
also sounds.

RIGHT Direction Arrow / MANUAL RUN / 
ENTER (G)

In SETUP MODE, saves entry, moves cursor in 
display one field to the right or to the next setup 
step.

In RUN MODE activates the pump for one com-
plete ON cycle if actuated during the OFF por-
tion of the RUN cycle.

UP and DOWN Direction Arrows (H)

Press and hold both the UP and DOWN Arrow 
keys together for 3 seconds to enter SETUP 
MODE. 

In SETUP MODE increase or decrease number 
values associated with the various RUN 
MODES.

LEFT Direction Arrow / RESET (J)

In SETUP MODE moves cursor in display one 
field to the left.

In RUN MODE, Pressing RESET starts a PUMP 
OFF cycle.

In ALARM MODE, Press once to clear buzzer; 
Press and hold for 3 seconds to clear warning 
and switch controller to OFF MODE.

NOTICE

To prevent damage to soft key buttons, do not press 
the buttons with sharp objects such as pens, plastic 
cards, or fingernails.

F

IG

. 1

ON

OFF

HH

MM

SS

##

!

J

D

F

A

B

C

E

H

G

Summary of Contents for GLC 2200



















Reviews: