background image

6

1.3.Factory.settings

Terminal’s.IP.address. ..

175.25.110.71

Terminal’s.network.address.

Serial.number

Administrator.password.

No.password

1.4.Package.contents.

Item

Number, pcs.

BioSmart.PV-WTC.Terminal.

1

Product.certificate

1

Installation.instructions

1

Mounting.kit.(two.6х35.dowels,.two.
3.5х38.self-tapping.screws)

1

2. USE, TRANSPORTATION AND STORAGE  
CONDITIONS

Abrasive.or.chemically.active.materials.should.not.be.used.to.clean.the.outer.surfaces.of.the.device.

or.the.palm.vein.scanner.

The.terminal.may.be.stored.in.the.following.environmental.conditions:

-.ambient.air.temperature.from.minus.40.to.plus.50.°С;

-.relative.air.humidity.(without.condensation).up.to.98%.

Water,.dust.and.other.foreign.substances.should.be.prevented.from.entering.the.inside.of.the.

terminal.during.transportation.and.storage..Following.storage.of.the.terminal.in.low.temperature.or.
high.humidity.conditions,.it.must.be.kept.in.a.dry.environment.at.a.temperature.of.(20±5).°С.for.no.
less.than.30.minutes.before.being.turned.on.

3. SAFETY REQUIREMENTS

To.avoid.malfunctions.in.the.terminal,.it.must.be.disconnected.from.its.power.source.before.any.

work.is.carried.out.with.its.case.open.

Only.specialists.authorized.by.the.manufacturers.of.this.terminal.should.carry.out.the.repair.and.

replacement.of.terminal.parts.

Summary of Contents for BioSmart PV-WTC-EM

























Reviews: