background image

Alternating Voltage Measurement with 1 MΩLoad Resistance and Frequency Measurement with Selectable 

Low-Pass Filter 

 

 

1.

 

In accordance with the voltage to be measured, turn the rotary switch to V~

1MΩ 

or 1kHz 

2.

 

Connect the measurement cables as shown. The „

“ should be gounded 

 

Voltage measurement: 

1.

 

You can switch back and forth between voltage measurement with and without low-pass filter 

2.

 

Press the FUNC | ENTER multifunction key repeatedly until the unit of measure V or. V/Fil appears at the display 

 

Frequency Measurement: 

1.

 

Apply the measured quantity in the same way as for voltage measurement 

2.

 

Manually select the measuring range for the voltage amplitude. When the instrument is switched to frequency measurement, the 
previously selected voltage measuring range remains active. 

3.

 

You can switch back and forth between frequency measurement with and without low-pass filter. Press the FUNC | ENTER 
multifunction key repeatedly until unit of measure Hz or Hz/Fil appears at the display 

 
 
 
 

 

 

 

 

 

 

Connection of the measurement cables 

 

 

 

 

 

 

 

 

Summary of Contents for SECULIFE HIT MD













Reviews: