Gorilla Playsets Rambler 1400 Owner'S Manual Download Page 85

Page: 85 / 94

STEP 53: ROCK WALL - ROPE AND ROCKS

1: PLACE ROCKS ON THE ROCK WALL IN A STAGGERED PATTERN AS SHOWN.

2: USE THE PAN HEAD SCREWS AND WASHERS INCLUDED WITH THE ROCK WALL ROCKS

TO ATTACH THEM TO THE ROCK WALL BOARDS.

3: SLIP THE ROCK WALL ROPE THROUGH THE HOLE IN THE SIDE RAIL. TIE A KNOT ON THE

INSIDE OF THE SIDE RAIL. YOU MAY TIE UP TO 3 KNOTS TO AID IN CLIMBING IF YOU WISH.

SLIP THE BOTTOM END OF THE ROCK WALL ROPE THROUGH THE HOLE IN THE BOTTOM

ROCK WALL BOARD. TIE A KNOT ON THE BACK SIDE OF THE ROCK WALL BOARD.

SAFETY CHECK - GO TO THE FRONT OF THE ROCK WALL AND GRAB THE ROPE IN YOUR

HAND. ATTEMPT TO TWIST THE ROPE AROUND YOUR HAND. IF THE ROPE WRAPS AROUND

YOUR HAND IT IS TOO LOOSE. UN-TIE THE KNOT UNDER THE BOTTOM ROCK WALL BOARD

AND RETIE IT UNTIL IT NO LONGER WRAPS AROUND YOUR HAND.

TIE KNOT BEHIND SIDE RAIL FIRST.

(PERFORM SAFETY CHECK)

TIE KNOT THIRD BEHIND BOTTOM ROCK WALL BOARD.

TIE KNOTS TO AID IN CLIMBING SECOND.

(UP TO 3 KNOTS MAY BE TIED)

SCALE 1 : 4

DETAIL A

WASHER

PAN HEAD SCREW

Summary of Contents for Rambler 1400































































































Search results

Summary of Contents for Rambler 1400

Reviews:

Related manuals for Rambler 1400

Brands by name

Popular brands

Gorilla Playsets Rambler 1400, Owner'S Manual

Search results

Summary of Contents for Rambler 1400

Reviews:

Related manuals for Rambler 1400

Brands by name

Popular brands