Gorilla Playsets Rambler 1400 Owner'S Manual Download Page 70

Page: 70 / 94

LAG SCREW

SIDE RAIL

SWING BEAM

3/8" X 9" CARRIAGE BOLT

TORQUE WASHER

3/8" X 3-1/2"

PLATE

3/8" WASHER

3/8" LOCK NUT

BOLT CAP

SWING BEAM

3/8" WASHER

POINTED END

OF SWING BEAM PLATE

* AN EXTRA PERSON IS NEEDED FOR THIS STEP.

1: ONE PERSON MUST LIFT THE SWING LEGS AND WALK AWAY FROM THE FORT WHILE A

PERSON ON THE DECK LIFTS THE OTHER END OF THE SWING BEAM.

2: ALIGN THE END HOLE OF THE SWING BEAM NEAREST THE FORT WITH THE MIDDLE HOLE

IN THE SWING BEAM PLATE.

3: INSERT A 3/8" X 9" CARRIAGE BOLT WITH TORQUE WASHER INTO THE HOLE IN THE SWING

BEAM. THE BOLT WILL GO THROUGH THE SWING BEAM, THROUGH THE SWING BEAM

PLATE AND THEN THROUGH THE SWING BEAM SIDE RAIL.

4: ALIGN THE SQUARE SHANK OF THE BOLT WITH THE SQUARE HOLE IN THE TORQUE

WASHER. SET THE TORQUE WASHER WITH A HAMMER BY STRIKING THE CARRIAGE BOLT.

5: FASTEN THE SWING BEAM TO THE FORT BY PLACING A 3/8" WASHER AND 3/8" LOCK

NUT ONTO THE END OF THE 9" CARRIAGE BOLT. PLACE A BOLT CAP OVER ANY EXPOSED

THREADS.

6: MAKE SURE THE SWING BEAM IS SQUARE TO THE SWING BEAM SIDE RAIL. ATTACH THE

POINTED END OF THE SWING BEAM PLATE TO THE SWING BEAM WITH A 3/8" X 3-1/2" LAG

SCREW AND 3/8" WASHER.

STEP 38: MOUNT SWING BEAM TO FORT

Summary of Contents for Rambler 1400































































































Search results

Summary of Contents for Rambler 1400

Reviews:

Related manuals for Rambler 1400

Brands by name

Popular brands

Gorilla Playsets Rambler 1400, Owner'S Manual

Search results

Summary of Contents for Rambler 1400

Reviews:

Related manuals for Rambler 1400

Brands by name

Popular brands