Gorilla Playsets Rambler 1400 Owner'S Manual Download Page 53

Page: 53 / 94

STEP 21: ROCK WALL

1: FLIP THE LADDER OVER SO THE FRONT SIDE IS FACING "UP".

2: PLACE A 2 X 4 X 54" ROCK WALL SIDE TO THE RIGHT OF THE LADDER. PLACE THE

LADDER AND THE ROCK WALL SIDE ON A FLAT SURFACE DURING CONSTRUCTION.

3: HAMMER A T-NUT INTO THE HOLE IN THE ROCK WALL SIDE ON THE OUTSIDE.

4: PLACE A 5/4 X 6 X 23-7/8" ROCK WALL BOARD AT THE TOP OF THE LADDER SIDE-RIGHT

AND ROCK WALL SIDE. THE TOP FACE OF THE ROCK WALL BOARD MUST BE FLUSH WITH

THE ENDS OF THE LADDER SIDE AND ROCK WALL SIDE.

5: PLACE THE REMAINING EIGHT ROCK WALL BOARDS FLUSH TO ONE ANOTHER AND

FLUSH TO THE SIDES OF THE LADDER SIDE AND ROCK WALL SIDE. PLACE THE BOTTOM

ROCK WALL BOARD FLUSH TO THE LAST ROCK WALL BOARD. THE BOTTOM ROCK WALL

BOARD IS ALSO FLUSH TO THE LADDER SIDE AND ROCK WALL SIDE. THE MIDDLE HOLE IN

THE BOTTOM ROCK WALL BOARD SHOULD BE OFFSET UP.

6: MAKE SURE ALL THE BOARDS ARE SQUARE TO THE ROCK WALL SIDE AND LADDER SIDE.

THEN ATTACH THE ROCK WALL BOARDS AND BOTTOM ROCK WALL BOARDS TO THE

LADDER SIDE AND ROCK WALL SIDE WITH #8 X 2" WOOD SCREWS.

5/4 X 6 X 23-7/8"

ROCK WALL BOARD

WITH FRONT

ROCK WALL SIDE.

ENDS OF LADDER SIDE AND

BOARDMUST BE FLUSH TO

(HOLE IS OFFSET UP)

BOTTOM ROCK WALL BOARD

5/4 X 6 X 23-7/8"

SCREW

WOOD

OF ROCK WALL SIDE.

END OF ROCK WALL SIDE

END OF LADDER SIDE

NOTE ANGLE

T-NUT ON OUTSIDE

#8 X 2"

TOP FACE OF ROCK WALL

"UP".

FACING

ROCK WALL SIDE

2 X 4 X 54"

LADDER SIDE - RIGHT

2 X 4 X 54"

LADDER

SHOWN

THIS IS THE

FRONT FACE

OF THE BOARD.

Summary of Contents for Rambler 1400































































































Search results

Summary of Contents for Rambler 1400

Reviews:

Related manuals for Rambler 1400

Brands by name

Popular brands

Gorilla Playsets Rambler 1400, Owner'S Manual

Search results

Summary of Contents for Rambler 1400

Reviews:

Related manuals for Rambler 1400

Brands by name

Popular brands