Gorilla Playsets Rambler 1400 Owner'S Manual Download

Page: 51 / 94

WOOD SCREW

T-NUT

NOTE ANGLE OF NOTCH ON EACH BOARD.

LADDER SIDE - LEFT

2 X 4 X 54"

LADDER SIDE - RIGHT

2 X 4 X 54"

LADDER STEP

2 X 4 X 22-3/4"

BOTTOM EDGE OF

STEPS MUST NOT

PROTRUDE PAST

BOTTOM OF LADDER

SIDES.

#8 X 2"

T-NUT

STEP 19: LADDER/ROCK WALL ASSEMBLY

OF THE LADDER SIDES. HAMMER THEM

INTO PLACE.

3: PLACE A 2 X 4 X 22-3/4" STEP IN EACH NOTCH. MAKE SURE THE BOTTOM EDGE OF

EACH STEP DOES NOT PROTRUDE PAST THE BOTTOM OF THE LADDER SIDES.

4: ATTACH EACH STEP TO THE LADDER SIDES WITH FOUR #8 X 2" WOOD SCREWS.

1: PLACE THE 2 X 4 X 54" LADDER SIDE - LEFT AND THE 2 X 4 X 54" LADDER SIDE - RIGHT ON

A FLAT SURFACE. THE LADDER IS SHOWN BELOW WITH THE "FRONT SIDE" FACING DOWN.

NOTE THE ANGLE OF THE NOTCHES. THE NOTCHES FOR THE STEPS SHOULD FACE EACH

OTHER ON THE INSIDE.

2: INSERT T-NUTS INTO THE HOLES ON THE OUTSIDE

NOTE: THIS VIEW IS THE LADDER WITH

THE "FRONT SIDE" FACING DOWN. THE

"FRONT SIDE" WILL BE THE BOTTOM

DURING THE CONSTRUCTION OF THE

LADDER IN THIS STEP.

Summary of Contents for Rambler 1400































































































Search results

Summary of Contents for Rambler 1400

Reviews:

Related manuals for Rambler 1400

Brands by name

Popular brands

Gorilla Playsets Rambler 1400, Owner'S Manual

Search results

Summary of Contents for Rambler 1400

Reviews:

Related manuals for Rambler 1400

Brands by name

Popular brands