Gorenje ONE DVG65W, Manual

Page: 24 / 56

EN 2
MOUNTING OF COOKER HOOD
x
Remove cooker hood from the packaging.
x
A part of packaging is the mounting guide – see
fig. 3.
x
Open the cooker hood and take off the fat
catching metal filter.
x
Place the mounting guide on the wall (bottom
edge of guide = bottom edge of cooker hood) and
mark the location of openings for the dowels in
the required height.
x
Drill the openings for the dowels on the marked
places „G“ and „H“. Tap the dowels into the bored
openings.
x
Screw in the screws into the dowels in the
openings „G“ and hang up the cooker hood on
them.
x
Lock the location of cooker hood with two screws
in the openings „H“.
IMPORTANT:
The horizontal location of cooker hood should
be observed.
THE EXHAUSTION VERSION
x
At use of exhaustion version (see fig. 4) the
exhalations are led into the exhaustion opening
with the exhaustion hose, which is connected to
the cooker hood with a flange. The exhaustion
hose and the fastening clips should be bought
additionally.
x
The exhaustion is provided through the upper
outlet of the cooker hood, on which the
exhaustion hose should be connected and the
other end of hose should be connected into the
exhaustion opening. The diameter of exhaustion
hose should be the same as the diameter of
connecting flange
– e.g. Ø 150mm, or Ø 120 mm
with a reduction piece (if you use connection hose
Ø 120 mm, you will decrease exhaust capacity
and increase noise level)
MOUNTING OF EXHAUSTION VERSION
AND OF DECORATION CHIMNEY
x
Fasten with help of a hose clip on the hinged on
cooker hood the one end of exhaustion hose,
fasten the other end into the exhaustion opening.
x
Both parts (the upper C and lower B) of
decoration chimney, shifted one to the other,
place on the hinged on cooker hood.
x
Shift the upper part C into the required height,
mark the upper location and mark the fastening
openings of console (K).
x
Remove the decoration chimney and bore the
marked openings for the dowels.
x
Screw on the console (K) together with cover of
decoration chimney (M).
x
Fasten once more the both parts of decoration
chimney, shift out its upper part and fasten to the
console with two screws.
IMPORTANT:
Remove protection foil from decoration chimney
not untill last assembly of decoration chimney!
IMPORTANT!
The carbon filter should not be installed in the
cooker hood at exhaustion version.
RECIRCULATION VERSION
x
A carbon filter and recirculation set should be
bought for the cooker hood in recirculation
version (fig. 9). The exhalations are exhausted
through the carbon filter.(fig. 1 (E)) The circulation
air with removed smell is led with exhausted hose
through air spreader to the ventilation openings in
upper part of decorative chimney to the room.
x
This version is used in cases, when there is no
waste air stack at disposal.
CAUTION!
The carbon filter should be installed in the
cooker hood at recirculation.
CONTROL (FIG. 6)
S – sensor of switching on/off function (sensor of
power switch)
L
– sensor of light switching on/off function
1, 2, 3 – sensors for setting on of capacity level
P – sensor of increased capacity function
(BOOSTER)
F
– signal light for signalling the pollution level for
the filter
C
– sensor of CLEAN and FRESH function
T – sensor of TIMER
CAUTION
x
The sensor touch control is activated with single
placing of finger on the corresponding symbol on
the control board. Therefore keep the control
board clean and dry.
x
Do not allow to children the use or cleaning of
appliance.
x
PREVENT the undesired switching on of
appliance, for instance with pets!
x
The set up parameters will be set to zero at
disconnection of cooker hood from the power.
The capacity of cooker hood can be regulated in
four levels using the touch symbols on the
control board. The reaction time of symbols is
0.5 seconds
– this is the necessary time for
holding the finger on the corresponding symbol.
SWITCHING ON OF COOKER HOOD
The sensor S is shining with lower intensity after
connecting the cooker hoods to the power net. With
pressing the S sensor (power switch) the cooker
hoods will be switched on
– the control board will
shining and activated.