background image

CHAPTER 1. INTRODUCTION

GÖPEL electronic GmbH

The device is intended for indoor use only and to be used only at an ambient temperature of 0 ° C - +45 ° C. It must

not be exposed to extreme temperatures, temperature fluctuations, heating and cooling systems, direct sunlight,

high levels of dust, vibration and impact, extreme humidity or moisture.

The device is only to be used in a technically perfect condition as well as in accordance with its intended use, in

a safety-conscious and hazard-conscious manner, observing the operating instructions! In particular, faults that

may affect safety must be rectified immediately!

1.3

EMC Protection Measures

The

G CAR 6282

Multibus Controller complies with the Electromagnetic Compatibility Directive (2014/30/EU).

In order to maintain electromagnetic compatibility, the system may only be operated in the delivered condition.

Mechanical and electrical modifications of any kind are not permitted. Only use suitable shielded signal and control

cables.

If the product is installed and operated in a system with other equipment, accessories and components,

the system as a whole and all its equipment, accessories and components must conform to the EMC

directives and standards. The system integrator is responsible for compliance with the EMC Directive

2014/30/EU and national EMC laws for installed systems, system accessories and system components

that have not been supplied or tested and approved by

GÖPEL electronic

as manufacturer of the equip-

ment.

1.4

General Safety Regulations

To avoid personal injury and / or property damage, follow these general safety instructions.

Risk of accident due to electric shock or fire

In addition to the operating instructions, observe the legal requirements and regulations for accident pre-

vention and environmental protection of the countries in which you operate the system.

Do not make any changes to the system without the written consent of the manufacturer.

Never operate damaged devices or components.

Keep liquids away from the unit and do not place any containers with liquid on the unit.

Danger of tripping or falling due to improperly laid cables

Lay cables so that nobody can step on them or trip over them.

Never try to stretch cables to enable a connection. The cables must always have enough clearance.

Damage caused by improper use or failure to observe the safety instructions and warnings is not covered by the

warranty. For consequential damages no liability is assumed by

GÖPEL electronic

!

G CAR 6282

2

Summary of Contents for G CAR 6282



































Reviews: